Nintendo Game Boy Advance SP Power Switch Cover Replacement
crwdns2944107:0crwdnd2944107:0DJ Pantonecrwdnd2944107:0crwdnd2944107:0crwdnd2944107:010crwdnd2944107:0crwdne2944107:0
crwdns2944111:0Dzi 18, 2025crwdne2944111:0
crwdns2915892:0crwdne2915892:0
crwdns2942287:0crwdne2942287:0This guide will walk you through the steps necessary to replace the power switch cover on your Game Boy Advance SP. The power switch of the Game Boy Advance SP is small and attaches to the motherboard itself. For this reason, the device features a much larger cover to help the user turn their device on and off. Follow this guide if your power switch cover is damaged or needs to be swapped out.
crwdns2942213:0crwdne2942213:0
crwdns2943213:0crwdne2943213:0
crwdns2943215:0crwdne2943215:0
crwdns2944105:0crwdne2944105:0
-
-
Use a standard Phillips #00 screwdriver to loosen the 4 mm screw that keeps the battery cover attached to the device.
-
-
-
Lift the battery cover up and remove it from the device.
-
-
-
Use your fingers or a plastic opening tool to remove the battery from the device.
-
-
-
Remove four 6.5 mm screws from the corners of the back cover using a tri-point Y00 screwdriver.
-
Remove two 4.6mm screws from the top-center and bottom-center of the device using a tri-point Y00 screwdriver.
-
-
-
Lift the back cover off of the device.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Lift the power switch cover away from the left side of the device using your fingers or tweezers.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:017crwdne2935229:0
crwdns2915084:0crwdne2915084:0
Cal Poly, Team 17-22, Forte Winter 2013 crwdns2935289:0Cal Poly, Team 17-22, Forte Winter 2013crwdne2935289:0
CPSU-FORTE-W13S17G22
crwdns2931471:04crwdne2931471:0
crwdns2935297:041crwdne2935297:0
crwdns2947412:03crwdne2947412:0
This doesn't explain anything about how to replace the switch
Maybe the guide was for replacing the power switch cover?
where to buy invidual y00,y0 or y1 bit?
Quel est le nom du vis svp je l'ai perdu et j'ai pas la référence
la chaîne de Samarium - crwdns2934203:0crwdne2934203:0
Bonjour @lachainede96340 D'après les instructions du tutoriel, il s'agit d'une vis Phillips (ou cruciforme) #00 de 4 mm de long. Ces mesures devraient suffire pour trouver une vis de remplacement dans votre stock de vis ou en magasin le cas échéant.
Claire Miesch -
Sorry if this is such a late response @lachainede96340, but the screw you're looking for is going to be 4mm long with a JIS/Phillips drive, M2 thread, and a pancake/wafer head.
Amazon Link
The head is most likely a pancake or wafer type head since it's not designed for a countersunk hole like a flat head, and is too thin to be a pan head. Hope this helps!
Désolé pour cette réponse si tardive @lachainede96340, mais la vis que tu cherches fait 4 mm de long, possède une empreinte JIS/Phillips, un filetage M2 × 0,4 mm et une tête pancake/wafer.
Lien Amazon (je n’ai pas réussi à trouver un lien sur le site Amazon France, désolé)
La tête est très probablement de type pancake ou wafer, car elle n’est pas conçue pour un trou fraisée comme une tête fraisée (flat head) et elle est trop fine pour être une tête bombée (pan head).
J’espère que ça t’aidera!
Stephen Posner -