Nothing Phone (1) Rear Glass Replacement

crwdns2931653:01crwdne2931653:0 Heat the rear glass

• Prepare an iOpener and apply it to the rear glass for at least two minutes to loosen the adhesive underneath.
• A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.
crwdns2913378:0crwdne2913378:0
crwdns2935263:02crwdne2935263:0
crwdns2934285:0crwdne2934285:0
Bereite einen iOpener* vor und platziere ihn für einige Minuten am rückseitigen Glas, um den Kleber darunter zu lösen.
*Ein Haarfön, eine Heissluftpistole und ähnliches könnte auch zum erwärmen verwendet werden. Dies aber BITTE mit Vorsicht, Akkus mögen zu starke Hitze nicht z.B.
byte park - N'w 8, 2022 crwdns2934203:0crwdne2934203:0
eine frage wo kann mn ne glassrückseite kaufen zum replacen
aoaoaoa aoaoaoa - Mha 23, 2023 crwdns2934203:0crwdne2934203:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0 Insert an opening pick




• Secure a suction handle to the bottom edge of the rear glass, as close to the edge as possible.
• If the rear glass is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.
• Lift the rear glass with the suction handle to create a small gap between the back cover and the frame.
• If you're having trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.
• Insert an opening pick into the gap you created.
• Slide the opening pick to the bottom right corner to slice the adhesive.
• Leave the opening pick in place to prevent the adhesive from resealing.
crwdns2913378:0crwdne2913378:0
crwdns2935263:04crwdne2935263:0
crwdns2934285:0crwdne2934285:0
.Einen Sauger unten am hinteren Glas anbringen, so nah wie möglich am Rand. i:Falls das Glas schon gesplittert ist, lässt sich der Sauger nicht verwenden. Man kann es mit einem starken Klebeband versuchen, oder man klebt den Sauger mit SuperKleber fest.
.Das rückseitige Glas minimal anheben, um einen kleinen Spalt zwischen der Rückseite und dem Rahmen zu erzeugen. i:Bei Problemen nochmals mit iOpener oder Wärmegeräten versuchen, den Kleber etwas zu lösen.
.Einen Plektrum bzw ein geeignetes Werkzeug in den geschaffenen Spalt einführen.
.'Schneiden' Sie mit dem Werkzeug durch den Kleber zur rechten unteren Ecke.
.Das Werkzeug nicht entfernen, um Wiederverkleben zu verhindern.
byte park - N'w 8, 2022 crwdns2934203:0crwdne2934203:0
Findet das jemand ganz ok übersetzt, oder sogar gut? mfg
byte park - N'w 8, 2022 crwdns2934203:0crwdne2934203:0
¿Dónde puedo conseguir el cristal trasero ya que se me rompió?
Alan Rodriguez - Yan 11, 2024 crwdns2934203:0crwdne2934203:0
Where can I buy the actual parts from ? I'm talking about the nothing phone (1) thank you for taking the time to read
Hady21t - Sun 20, 2025 crwdns2934203:0crwdne2934203:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0 Slice the adhesive
• Insert a second opening pick at the bottom edge of your phone.
• Slide the opening pick to the bottom left corner to slice the adhesive.
• Leave the opening picks in place to prevent the adhesive from resealing.
crwdns2913378:0crwdne2913378:0
crwdns2935263:02crwdne2935263:0
crwdns2934285:0crwdne2934285:0
Hello help please! I'm in France and I'm desperate to find the back glass for my Nothing Phoane 1help me with a link outside india where i can find? India does not ship to France
costache marius - N'w 6, 2023 crwdns2934203:0crwdne2934203:0
try https://nl.aliexpress.com/item/100500675... or https://www.amazon.in/nothing-phone-1-ba...
frey_code - Sun 27, 2025
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0 Slice the adhesive
• When you slice near the glyph, insert only the tip of the opening pick (~2-3 mm) to avoid damaging the LEDs.
• If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener for one to two minutes to reheat it.
• Insert a third opening pick at the bottom left corner of your phone.
• Slide the opening pick along the left edge of your phone to slice the adhesive.
• Leave the opening pick in the top left corner to prevent the adhesive from resealing.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0
• Insert a fourth opening pick underneath the top left corner of your phone.
• Slide the opening pick along the top edge to slice the adhesive.
• Leave the opening pick in the top right corner to prevent the adhesive from resealing.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0
• Insert a fifth opening pick underneath the top right corner.
• Slide the opening pick along the right edge of the rear glass to slice the remaining adhesive.
• At this point, the rear glass should be separated from the frame. If there's still resistance around the edges of the glass, use an opening pick to separate any remaining adhesive.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:07crwdne2931653:0 Remove the rear glass

crwdns2935267:0crwdne2935267:0
Dust Blower
$4.99
crwdns2945778:0crwdne2945778:0
• Remove the rear glass.
• Apply new adhesive where necessary after cleaning the relevant areas with isopropyl alcohol (>90%).
• Since the rear glass of the Nothing Phone (1) is transparent a dust blower may come in handy for cleaning before installing a new rear glass.
• Secure the new back cover with pre-cut adhesive or double-sided adhesive tape. After installing the back cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.
crwdns2913378:0crwdne2913378:0
crwdns2935263:03crwdne2935263:0
crwdns2934285:0crwdne2934285:0
Bonjour,
La vitre arrière est introuvable.
C'est scandaleux..
Stéphane 34 - Nhl 4, 2023 crwdns2934203:0crwdne2934203:0
Bonjour @stephane34,
Nous n’avons malheureusement pas de pièces pour le Nothing Phone. J'ai transmis la demande à notre département d'achat.
Bonne continuation de vos recherches !
Claire Miesch - Nhl 10, 2023
Nothing phone 1 real glass kidar milega
Nothing 1 - N'w 18, 2023 crwdns2934203:0crwdne2934203:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935291:0crwdnd2935291:01crwdnd2935291:0crwdne2935291:0

Dominik Schnabelrauch

crwdns2935283:011/23/16crwdne2935283:0

232,252 crwdns2915208:0crwdne2915208:0

crwdns2935297:0682crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 40

• 
• 
• 

crwdns2935301:037crwdne2935301:0

crwdns2915084:0crwdne2915084:0

iFixit crwdns2935289:0iFixitcrwdne2935289:0

Staff

crwdns2931471:0121crwdne2931471:0

crwdns2935297:019,857crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0