crwdns2915892:0crwdne2915892:0
Use this guide to replace the logic board in your iPhone 6s Plus.
It's important to note that each iPhone's logic board and Touch ID fingerprint sensor are paired at the factory, so replacing the logic board will disable Touch ID unless you also install a replacement home button that has been properly paired to your new logic board.
crwdns2942213:0crwdne2942213:0
-
-
Power off your iPhone before beginning disassembly.
-
Remove the two 3.6 mm P2 Pentalobe screws next to the Lightning connector.
-
-
crwdns2935267:0crwdne2935267:0Clampy - Anti-Clamp$24.95
-
Pull the blue handle backwards to unlock the Anti-Clamp's arms.
-
Slide the arms over either the left or right edge of your iPhone.
-
Position the suction cups near the bottom edge of the iPhone just above the home button—one on the front, and one on the back.
-
Squeeze the cups together to apply suction to the desired area.
-
-
-
Pull the blue handle forwards to lock the arms.
-
Turn the handle clockwise 360 degrees or until the cups start to stretch.
-
Insert an opening pick or tool under the screen when the Anti-Clamp creates a large enough gap.
-
Skip the next three steps.
-
-
-
Use a single suction cup to lift the front panel:
-
Press a suction cup onto the screen, just above the home button.
-
-
-
While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel assembly from the rear case.
-
Using a plastic opening tool, begin to gently pry the rear case down, away from the display assembly, while continuing to pull up with the suction cup.
-
-
-
Pull the plastic nub to release the vacuum seal on the suction cup.
-
Remove the suction cup from the display assembly.
-
-
-
Pull the home button end of the front panel assembly away from the rear case, using the top of the phone as a hinge.
-
Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.
-
Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.
-
-
-
Remove the following Phillips screws from the battery connector bracket:
-
One 2.3 mm screw
-
One 3.1 mm screw
-
-
-
Remove the metal battery connector bracket from the iPhone.
-
-
-
Use a clean fingernail or the edge of an opening tool to gently pry the battery connector up from its socket on the logic board.
-
-
-
Remove the following Phillips screws securing the front panel assembly cable bracket:
-
Three 1.2 mm screws
-
One 1.5 mm screw
-
One 2.9 mm screw
-
-
-
Remove the front panel assembly cable bracket from the logic board.
-
-
-
While still supporting the front panel, use a fingernail or the edge of an opening tool to disconnect the front-facing camera and earpiece speaker connector.
-
-
-
Disconnect the home button cable connector.
-
-
-
Use a plastic opening tool to disconnect the display data cable connector.
-
-
-
-
Finally, disconnect the digitizer cable connector.
-
-
-
Remove the front panel assembly from the rear case.
-
-
-
Remove the following screws securing the antenna bracket to the rear case:
-
One 1.5 mm Phillips #00 screw
-
One 2.8 mm Phillips #00 screw
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Grasp the 5GHz Wi-Fi antenna bracket with a pair of tweezers and lift it off the iPhone.
-
-
-
Carefully pry the 5GHz Wi-Fi antenna connector up off the logic board with a plastic opening tool.
-
-
-
Grasp the 5GHz Wi-Fi antenna connector with a pair of tweezers and gently lift it from its retaining clip on the logic board.
-
-
-
Disconnect the power button cable and audio control cable connectors from their respective sockets on the logic board.
-
-
-
Remove the following screws securing the 5GHz Wi-Fi antenna to the rear case:
-
One 2.8 mm Phillips #00 screw
-
Two 1.6 mm Phillips #00 screws
-
-
-
Use a pair of tweezers to grasp and remove the 5GHz Wi-Fi antenna out of the iPhone.
-
-
-
Pry the charge port connector cable up from its socket on the logic board with the flat end of a spudger.
-
-
-
Use the tip of a spudger to disconnect the interconnect antenna cable from its socket on the logic board.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Grasp the interconnect antenna cable with a pair of tweezers and carefully de-route it from its channel on the vibrator assembly.
-
-
-
Remove the two 2.5 mm Phillips #00 screws securing the vibrator to the rear case.
-
-
-
Remove the vibrator from the iPhone.
-
-
-
Insert a SIM card eject tool or a paperclip into the small hole in the SIM card tray.
-
Press to eject the tray.
-
-
-
Remove the SIM Card tray assembly from the iPhone.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Use a pair of tweezers to peel back the piece of tape covering the hidden screw securing the rear-facing camera bracket to the rear case.
-
-
-
Remove the following screws securing the rear-facing camera bracket to the rear case:
-
One 1.7 mm Phillips #00 screw
-
One 2.3 mm Phillips #00 screw
-
-
-
Lift and remove the rear-facing camera bracket off the rear-facing camera.
-
-
-
Use the flat end of a spudger to disconnect the rear-facing camera connector from its socket on the logic board.
-
-
-
Carefully lift and remove the rear-facing camera out of the iPhone.
-
-
-
Remove the single 2.8 mm Phillips #00 screw securing the plastic clip to the logic board.
-
-
-
Remove the single 1.3 mm Phillips #00 screw recessed against the top of the rear case.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Use a pair of tweezers to firmly grasp the plastic clip and remove it from the iPhone.
-
-
-
Remove the single 1.6 mm Phillips #00 screw securing the antenna clip to the rear case.
-
-
-
Carefully grasp the antenna clip with a pair of tweezers and remove it from the iPhone.
-
-
crwdns2935267:0crwdne2935267:0Standoff Screwdriver for iPhones$5.49
-
Remove the following screws securing the logic board to the rear case:
-
Two 2.4 mm standoff screws
-
One 2.1 mm Phillips #00 screw
-
-
-
Carefully raise—but do not remove—the logic board, lifting it from the bottom edge nearest the Lightning connector.
-
-
-
Continue carefully lifting the bottom side of the logic board until it is vertical.
-
-
-
Gently lay the logic board upside-down, with the top portion resting against the rear case of the iPhone.
-
Use the flat end of a spudger to disconnect the antenna connector from its socket on the back of the logic board.
-
-
-
Lift and remove the logic board out of the iPhone.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:0185crwdne2935229:0
crwdns2947412:031crwdne2947412:0
Hello. Good job on these teachings of disassembly. I need help in changing the logic board of my iphone 5 and iphone 6. Where can i buy the logic board? I reside in Nigeria
HI do you know who replaces logic boards on iPhone 6?
I am on Step 29 and the upper-right screw was stripped in manufacturing and I am not able to remove? What is the best way to remove the stripped screw?
if u can melt a pen and stick it on then twist it if that dosen’t work use a dermel cut the screw and use a flahead
Is there anyone who has this service Im willing to pay someone who's legit
