crwdns2915892:0crwdne2915892:0
Follow this guide to replace the guard plate on a 2017 Toro Stump Grinder model 22615HD.
crwdns2942213:0crwdne2942213:0
-
-
Turn the ignition switch to the off position.
-
-
-
Flip the fuel cutoff valve switch into the off position.
-
-
-
Grab the plastic housing at the end of the spark plug wire.
-
Pull firmly to disconnect the wire from the spark plug.
-
-
-
Tilt the machine so that it is resting on the handle with the cutter wheel raised.
-
-
-
Use a 14 mm socket to remove the fasteners securing the belt guard:
-
One 10 mm bolt
-
One 10 mm nut
-
-
-
Use a 9/16 inch socket to loosen the four nuts securing the bottom of the motor enough to allow the motor to slide freely. Do not remove the nuts.
-
Use a 1/2 inch wrench in combination with the socket wrench to hold the bolts in place.
-
-
-
Use a 1/2 inch wrench to loosen the two bolts behind the centrifugal clutch enough to allow the motor to slide freely. Do not remove the bolts.
-
-
-
-
Wrap a piece of tape around the upper half of the tensioner bolt to mark the location of the second nut.
-
Use a 9/16 inch wrench to loosen the nut on the lower half of the tensioner bolt until the motor can slide forward as much as possible.
-
-
-
Slide the engine towards the cutter blade to loosen the drive belt.
-
-
-
Lift the drive belt up and away from the machine while rolling it towards the cutter head to gradually roll it off of the pulley.
-
-
-
Use an impact wrench with a 9/16 inch socket to remove the bolt and washer securing the centrifugal clutch to the spindle.
-
-
-
Use a jaw puller to extract the centrifugal clutch from the spindle:
-
Place the center screw so that it is in line with the center of the spindle.
-
Hook the jaws around the back edge of the clutch assembly.
-
Tighten the center screw until the centrifugal clutch is removed from the spindle.
-
-
-
Remove the centrifugal clutch and shaft key from the spindle.
-
-
crwdns2931653:016crwdne2931653:0 Remove the pulley
crwdns2944590:016crwdnd2944590:018crwdnd2944590:0crwdnd2944590:0crwdne2944590:0
-
Use a 1/8 inch hex key to remove the pulley set screw.
-
-
-
Use a universal puller to remove the pulley from the cutter wheel shaft:
-
Attach the universal puller to the pulley using the three bolts provided on the pulley.
-
Use a wrench to torque down the center screw to slowly loosen the pulley.
-
-
-
Pull the pulley off of the shaft to remove it.
-
Remove the shaft key.
-
-
-
Use a 9/16 inch socket to remove the two bolts and washers securing the guard plate to the motor.
-
-
-
Use a 9/16 inch socket to remove the bolt and washer securing the guard plate to the frame.
-
Use a 5/8 inch wrench in combination with the 9/16 inch socket to hold the standoff in place.
-
Remove the bolt, washer, and standoff.
-
-
-
Use a 9/16 inch socket to remove the bolt and accompanying washer securing the guard plate to the frame.
-
-
-
Use a 5/8 inch socket to remove the nut securing the guard plate to the frame.
-
-
-
Use a 1/2 inch socket to remove the bolt next to the cutter wheel shaft securing the guard plate to the frame.
-
-
-
Remove the guard plate from the frame.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
