crwdns2915892:0crwdne2915892:0
Use this guide to replace the motherboard in your Huawei P10 Lite smartphone.
crwdns2942213:0crwdne2942213:0
-
-
Insert the tip of an opening pick between the back cover and the mid frame and slide it around the phone, to cut the adhesive.
-
Using a suction handle to lift the back cover may help to get an initial gap for the opening pick to put in.
-
-
-
After you cut the adhesive on every edge, twist your opening pick, to separate the rear cover from the phone.
-
Flip the rear cover over to the right side of the phone.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Use a pair of tweezers to remove the sticker.
-
Remove the two Phillips #00 screws.
-
Remove the four 2.5 mm Phillips #00 screws.
Schritt 3 und 4 kann man sich komplett sparen. Wozu auch. Kann gleich mit Schritt 5 weitergemacht werden, zuvor einfach das Flachbandkabel vom Fingerabdrucksensor an der Rückabdeckung abklemmen und fertig.
There are four silver screws and two black to be removed.
Translate what Bobby mcgee said:
Step 3 and 4 can be completely ignored. What for? You can continue with step 5, just disconnect the ribbon cable from the fingerprint sensor on the back cover and you're done.
However, the reason step 3 and 4 should not be skipped is Step 6 — Use an iOpener to loosen the adhesive beneath the battery. I.e., the adhesive cannot be easily removed without heat, however, that heat might damage the electric chips. Thus they’d better be removed first.
-
-
-
-
Use tweezers to remove the mainboard shield.
-
Use the flat end of a spudger to disconnect the finger print sensor flex cable.
Welchen Klebstoff soll man verwenden?
Hallo Josef,
sollte bei deinem Ersatzteil kein Klebstoff oder Klebeband dabei gewesen sein, kannst du dünne Streifen Doppelseitiges Klebeband verwenden. Es gibt für das Huawei P10 Lite auch schon zugeschnittene Klebestreifen zu erwerben, hierbei gilt aber je nach Händler Rezessionen zu lesen, ob die Klebestreifen auch wirklich halten.
Note that there is a copper-colored sticker to lift up near the flat cable connected from the phone the finger pad. Lift the main board plate (shield) up SLOWLY from the camera side to the other end as the plate is wedged in place.
what adhesive is recommended? thanks
Hi darren,
pre-cut adhesive would be the best solution if you can source it. Otherwise a two-sided adhesive tape or carefully used E6000 adhesive glue will be your friend. -
-
-
Use a SIM card removal bit or tool and push it into the small hole in the SIM card tray.
-
Remove the SIM card tray.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Remove the three Phillips #000 screws.
-
Use tweezers to remove the two metal shields which cover the flex cables on the mainboard.
-
-
-
Use the flat end of a spudger to disconnect the volume and power button, the display and the main flex cable.
-
-
-
Disconnect the battery flex cable with a spudger.
-
Unplug the antenna cable with tweezers.
-
-
-
Disconnect the headphone jack flex cable with the flat end of a spudger.
-
Use an opening pick to pry out the motherboard until you can get a good grip.
-
Remove the motherboard.
Clear and to the point. Many thanks…
Where to buy new motherboard original huawei.
-
To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.
To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.
crwdns2935221:0crwdne2935221:0
crwdns2935229:08crwdne2935229:0
crwdns2947412:02crwdne2947412:0
ma la scheda di ricambio dove la trovo?
I need huawei p10 lite board 4gb 64gb
Mit dem Saugnapf die Rückseite anheben hilft ungemein…
Matthias Eberle - crwdns2934203:0crwdne2934203:0
Had to use blue wedge tool to wedge open bottom plate from the rim part in order to then use the tip of the blue opening pick under the back plate to then cut the glue. It’s like placing a pie server or knife under the plate once there’s a gap between the rim and the back plate.
Jane - crwdns2934203:0crwdne2934203:0
Be careful, there’s a cable to fingerprint sensor, very close to the edge (see pictures below)… It’s very easy to cut it through with the pick, as I just learned :)
dambig - crwdns2934203:0crwdne2934203:0