crwdns2933423:0crwdne2933423:0

Molinillo BCG800XL atascado debido al desgaste del impulsor

crwdns2936315:0crwdne2936315:0
crwdns2936331:0crwdne2936331:0
crwdns2931653:020crwdne2931653:0
BCG800XL Grinder Jamming due to Worn Impeller, Troubleshooting #2 - Burr Clearance: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 BCG800XL Grinder Jamming due to Worn Impeller, Troubleshooting #2 - Burr Clearance: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 BCG800XL Grinder Jamming due to Worn Impeller, Troubleshooting #2 - Burr Clearance: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Troubleshooting #2 - Burr Clearance
  • TOO CLOSE (ie: grinding too fine): If the burrs are too close, or even touching (but centered), the nut on the lower burr may not be tight enough. With the ratchet and 10mm socket, give it a quick counter-clockwise jerk. If that fails, recheck your fit-up against the second photo to make sure the lower conical burr is the proper height.

  • If it's clear that the lower burr is sitting too high on the impeller, see the 3rd picture and sand the area highlighted in RED. While doing this, periodically install and re-check the lower burr height until it matches photo #2. Careful not to sand off too much as it's easy to remove thickness but hard to add it back.

  • TOO FAR: If the burrs are too far apart such that the grind isn't fine enough, it could be that the steel washer underneath the impeller got left out. See step #9. Additionally, you can try removing *one* of the two washers above the lower burr and not tightening the nut as much. There's also a shim kit offered by Breville if you contact them.

  • Lastly, both of the above issues can happen if the alignment in "Step 12" got shifted. If so, you may need to pop-off and adjust the rotation of the upper-burr holder assembly. This is tricky, but doable. I suggest marking the existing alignment with permanent marker before experimenting.

DEMASIADO CERCA (afilado demasiado fino): Si las fresas están muy cerca o tocándose (pero centradas), puede que la tuerca de la fresa inferior no esté bien apretada. Con la carraca y el enchufe de 10 mm, da un tirón rápido (sentido antihorario). Sino comprueba el ajuste con la segunda foto y ve que la fresa cónica inferior tenga la altura correcta.

Si es evidente que la rebaba inferior está demasiado alta en el impulsor, consulta la tercera imagen y lija el área resaltada en ROJO. Mientras tanto, instala y vuelve a verificar periódicamente la altura de la rebaba inferior hasta que coincida con la foto n.° 2. Ten cuidado de no lijar demasiado, es fácil quitar grosor, pero difícil recuperarlo.

DEMASIADO LEJOS: Si las fresas están muy separadas, impide que la molida sea lo bastante fina, puedes haber omitido la arandela de acero bajo el impulsor. Ve el paso 9. Además, puedes intentar quitar *una* de las dos arandelas sobre la fresa inferior y no apretar tanto la tuerca. Breville también ofrece un kit de calzas si contactas con ellos.

Por último, ambos problemas pueden ocurrir si la alineación del "Paso 12" se desplazó. En ese caso, podrías necesitar desmontar y ajustar la rotación del conjunto del portafresas superior. Esto es complicado, pero factible. Te sugiero marcar la alineación existente con un marcador permanente antes de experimentar.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0