crwdns2933423:0crwdne2933423:0

Sostituzione batteria Motorola Moto X Pure Edition

crwdns2936315:0crwdne2936315:0
crwdns2936321:0crwdne2936321:0
crwdns2931653:02crwdne2931653:0
Motorola Moto X Pure Edition Battery Replacement: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Motorola Moto X Pure Edition Battery Replacement: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Motorola Moto X Pure Edition Battery Replacement: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
  • Try to keep the adhesive strips flat and unwrinkled during this procedure; twisted or wrinkled strips will stick together and break instead of pulling out cleanly.

  • Additionally, do not press down on the battery as you pull the strips. Pressing on the battery creates pressure points that can snag and break the adhesive.

  • Grasp one of the battery adhesive tabs with your fingers and slowly pull it away from the battery, towards the bottom of the phone.

  • Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the midframe. For best results, pull the strip at as low an angle as possible, without snagging it on any other components.

  • The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.

  • If the battery adhesive tabs break during the removal process, use your fingers or blunt tweezers to retrieve the remaining length of adhesive, and continue pulling.

  • If any of the adhesive strips break underneath the battery and cannot be retrieved, try to remove the remaining strip, and then proceed with the rest of the steps.

Nel corso di questa procedura, cerca di tenere le strisce adesive piatte e non arricciate, altrimenti le strisce si appiccicheranno tra loro e si romperanno invece di venire via senza problemi.

Inoltre, non devi premere sulla batteria mentre tiri le strisce. Schiacciare la batteria crea dei punti di pressione che possono intrappolare le strisce e romperle.

Afferra una delle linguette adesive della batteria con le dita e, lentamente, tirala in direzione opposta alla batteria, verso il fondo del telefono.

Tira in modo continuo, mantenendo una tensione costante sulla striscia finché non scivola fuori da sotto la batteria e il telaio centrale. Per risultati ottimali, tira la striscia tenendola all'angolo più basso possibile, ma senza farla impigliare su altri componenti.

La striscia si allungherà di diverse volte la sua lunghezza originaria. Continua a tirare e, se necessario, riafferra la striscia più vicino alla batteria.

Se le linguette adesive della batteria si rompono durante il processo di rimozione, usa le dita o delle pinzette a punte arrotondate per recuperare la parte rimanente della striscia e prosegui a tirare.

Se una delle strisce adesive si rompe sotto la batteria e non può essere recuperata, cerca di rimuovere la striscia rimasta e poi procedi in base agli altri passi.

[* icon_caution] Try to keep the adhesive strips flat and unwrinkled during this procedure; twisted or wrinkled strips will stick together and break instead of pulling out cleanly.
[* icon_caution] Additionally, do not press down on the battery as you pull the strips. Pressing on the battery creates pressure points that can snag and break the adhesive.
[* black] Grasp one of the battery adhesive tabs with your fingers and ***''slowly''*** pull it away from the battery, towards the bottom of the phone.
[* black] Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the midframe. For best results, pull the strip at as low an angle as possible, without snagging it on any other components.
[* icon_note] The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.
-[* black] If the battery adhesive tabs break during the removal process, use your fingers or blunt tweezers to retrieve the remaining length of adhesive, and continue pulling.
+[* black] If the battery adhesive tabs break during the removal process, use your fingers or [product|IF145-020-4|blunt tweezers] to retrieve the remaining length of adhesive, and continue pulling.
[* icon_note] If any of the adhesive strips break underneath the battery and cannot be retrieved, try to remove the remaining strip, and then proceed with the rest of the steps.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0