crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

修复死亡黄灯

crwdns2933809:0crwdne2933809:0

crwdns2935433:0crwdne2935433:0

PS3的智能板更换

更换PS3的顶盖

PS3的蓝光驱动器更换

PS3的主板更换

PS3 电源接口更换

PS3 后面板更换

PS3 散热器更换

PS3主板更换

crwdns2935443:0crwdne2935443:0

= crwdns2915112:0crwdne2915112:0 = crwdns2861241:0crwdne2861241:0
crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
    [video|http://www.youtube.com/watch?v=uMG-6rbanlY]
    Use this guide to potentially repair PlayStation 3s with the "Yellow Light of Death" error.
    '''Note:''' Your PlayStation may look slightly different inside. Be cautious when performing this process on your machine.
    This procedure may not completely revive your console. Since the “Yellow Light of Death” is a generic hardware error, the issue can range from an overheating CELL/RSX from dried thermal paste underneath the IHS, bad NEC/TOKIN capacitors, a short on the board, faulty RSX, etc. This guide may only temporarily fix consoles with a faulty flip chip (most likely RSX but CELL could also be at fault). An RSX/CELL replacement (requiring a BGA rework station) would be required to permanently repair a console with a faulty flip chip.
    ***Note:*** Your PlayStation may look slightly different inside. Be cautious when performing this process on your machine.
      To reassemble your device, follow these instructions in reverse order starting at [http://www.ifixit.com/Guide/Yellow+Light+of+Death+Repair/guide|3654/1#s16714|step 41|stepid=16714].

      crwdns2931349:0crwdne2931349:0

      crwdns2936071:01crwdne2936071:0

      使用撬棍的平头，从主板上的CPU和GPU上刮掉旧的散热硅脂。

      crwdns2936071:02crwdne2936071:0

      使用手指或撬棍的平头，按照指示移除逻辑电路板上的旧散热垫。

      crwdns2936071:03crwdne2936071:0

      将热枪设置为“低”，让其运行几分钟以达到工作温度。

      crwdns2936071:04crwdne2936071:0

      将主板放置在支架上，使 CPU 和 GPU 得到完全的支撑和水平等高。

      crwdns2936071:05crwdne2936071:0

      使用圆周运动，均匀加热（使用低热）四个区域中的每一个区域大约25秒。

      crwdns2936071:06crwdne2936071:0

      继续使用与上述相同的圆周运动加热芯片约 25 秒。

      crwdns2936071:07crwdne2936071:0

      在继续本指南之前，请确保主板已经完全冷却。

      crwdns2936071:08crwdne2936071:0

      在所示位置将新的散热垫贴到主板上：

      crwdns2936071:09crwdne2936071:0

      将剩余的白色塑料贴纸从热垫的另一面剥下。

      crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0