crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

认识和断开线缆连接头

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
crwdns2931653:06crwdne2931653:0
Recognizing & Disconnecting Cable Connectors, Press Connectors: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Recognizing & Disconnecting Cable Connectors, Press Connectors: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Recognizing & Disconnecting Cable Connectors, Press Connectors: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Press Connectors

  • Press (or "pop") connectors are found at the end of a ribbon cable and have a flat, metal or plastic top—typically rectangular. These connectors are extremely common in smartphones and laptops, and connect a wide variety of small to medium-sized cables—screen, battery, board interconnect, etc.

  • Place a spudger or an opening tool under the connector's edge and pry straight up to disconnect it.

  • Make sure to pry under the edge of the connector itself, and not under the socket on the board. Otherwise, you risk permanently damaging the socket.

  • Work carefully: don't pry on or accidentally scrape any small, surface mounted components on the board.

  • Although more rare, some larger pop-style connectors might have a built-in pull-tab for easy disconnection. Lift straight up to disconnect these.

  • To reconnect, align the connector carefully over its socket and press down with your fingertip—first on one of the short sides, then the other—until it clicks into place. Don't try to force the connector into place. If you're having trouble, reposition it and try again.

  • Don't press down on the middle of wider connectors until they're fully seated. If misaligned, the connector or the pins underneath can bend or break, causing permanent damage.

冲压连接器

压入式（或 "弹出式"）连接器位于带状电缆的末端，顶部为扁平的金属或塑料，通常为矩形。这种连接器在智能手机和笔记本电脑中极为常见，用于连接各种中小型电缆--屏幕、电池、电路板互连等。

将塞子或开口工具放在连接器边缘下方，然后向上撬动以断开连接。

确保撬到的是连接器本身的边缘，而不是电路板上的插座。否则有可能永久损坏插座。

小心操作：不要撬动或意外刮伤电路板上任何表面安装的小型元件。

虽然比较少见，但一些较大的弹出式连接器可能有一个内置拉环，便于断开连接。直接向上提起即可断开连接。

要重新连接，请小心地将连接器对准插座，然后用指尖向下按压，先按住其中一个短边，再按住另一个短边，直到卡入到位。不要强行将连接器按到位。如果遇到困难，请重新定位再试一次。

在连接器完全就位之前，不要按压较宽连接器的中部。如果错位，连接器或下面的插针可能会弯曲或断裂，造成永久性损坏。

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0