crwdns2933423:0crwdne2933423:0

Google Pixel 8 スクリーンの交換

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:012crwdnd2931529:0crwdne2931529:0

crwdns2935425:021crwdne2935425:0

crwdns2936315:0crwdne2936315:0
crwdns2936323:0crwdne2936323:0
crwdns2931653:021crwdne2931653:0
Google Pixel 8 Screen Replacement, Reassembly information: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Google Pixel 8 Screen Replacement, Reassembly information: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Google Pixel 8 Screen Replacement, Reassembly information: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Reassembly information
  • If you're installing a new screen with pre-installed adhesive, follow this step during reassembly. Otherwise, follow this guide to apply adhesive to your old screen.

  • Use the pull tabs to remove the liners covering the front camera cutout, the rear camera pad, the back of the screen, and the perimeter adhesive.

  • Reconnect the screen cable and reinstall its cover.

  • This is a good point to test your phone before sealing it up. Temporarily power on your phone and make sure it works as expected. Power it down before continuing.

  • Firmly press the screen into place on the frame. You should feel the clips "pop" into place.

  • Press firmly around the perimeter of the screen to secure it with the new adhesive.

  • Optionally, you can strengthen the adhesive bond by applying pressure evenly to the phone.

  • Follow this guide to calibrate the fingerprint sensor.

取り付ける新しいスクリーンに予め両面テープが貼り付けられている場合は、この手順に沿って作業を続けて下さい。スクリーンに両面テープが貼られていない場合は、こちらのガイドに従ってスクリーンに両面テープを貼って下さい。

このタブを使ってライナーを取り除いて下さい。このライナーはフロントカメラの切り欠き、背面カメラのパッド、スクリーンの背面及び縁の両面テープを覆っています。

スクリーンケーブルを接続し直して、スクリーンケーブルカバーも取り付け直して下さい。

スクリーンを接着する前に正しく機能するかどうか確認するなら、この時点で行いましょう。一時的に電源を入れ、正常に動作するか確認しましょう。組み立てを再開する前に、必ず電源を切りましょう。

スクリーンを筐体の正しい位置に合わせてからしっかり押し付けて下さい。クリップが正しい位置に収まる「ポンッ」という感触を感じるはずです。

スクリーンの端周辺をしっかり押し付けて、新しい両面テープをしっかり貼り付けます。

スクリーンをよりしっかり接着するためにデバイスの縁を均等に押さえつけることもできます。

こちらのガイドに従って指紋センサーのキャリブレーションを行って下さい。

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0