crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

開口方法

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:019crwdnd2931529:0crwdne2931529:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936323:0crwdne2936323:0
crwdns2931653:017crwdne2931653:0
Opening Procedure, Tip for removing EMI shields: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Opening Procedure, Tip for removing EMI shields: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Opening Procedure, Tip for removing EMI shields: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Tip for removing EMI shields

  • Use this method to remove any EMI shields necessary during your repair:

  • Use one tip of a pair of angled tweezers to pry up the EMI shield from the gaps between the "teeth."

  • Repeat this procedure at different points around the perimeter of the shield until it is free.

  • Try not to deform the shields too much—you will need to reinstall them during reassembly.

  • To reinstall, correct any deformations to the best of your ability, make sure the "teeth" align with the rim on the motherboard, and press down on the entire perimeter of the EMI shield.

  • Make sure all "teeth" are snug to the metal rim and not bent underneath the EMI shield.

  • Make sure the "teeth" are also touching the gold conductive strips on the top of ribbon cables.

EMIシールドを外す際のヒント

この手順は、修理作業中、EMIシールドを外す外すために必要です。

アングル付きピンセットの先端の片側を使って、"歯 "の間の隙間からEMIシールドをかき出します。

シールド周辺の違うポイントでもこの手順を繰り返して、シールドを外してください。

再組み立ての際は、このシールドを変形させないようにご注意ください。

再組み立ての際には、変形しないように位置合わせをして、”歯”がマザーボード上の淵に合っていることを確認して、EMIシールド全体を押してください。

すべての”歯”がメタルの淵にぴったりとはまり、EMIシールドの下で曲がっていないことを確認してください。

[title] Tip for removing EMI shields
[* icon_note] Use this method to remove any EMI shields necessary during your repair:
[* black] Use one tip of a pair of [product|IF145-020-5|angled tweezers] to pry up the EMI shield from the gaps between the "teeth."
[* black] Repeat this procedure at different points around the perimeter of the shield until it is free.
[* icon_caution] Try not to deform the shields too much—you will need to reinstall them during reassembly.
[* icon_reminder] To reinstall, correct any deformations to the best of your ability, make sure the "teeth" align with the rim on the motherboard, and press down on the entire perimeter of the EMI shield.
[* icon_caution] Make sure all "teeth" are snug to the metal rim and not bent underneath the EMI shield.
+ [* icon_caution] Make sure the "teeth" are also touching the [link|https://guide-images.cdn.ifixit.com/igi/ZsTLUVefcIOQiH5M.full|gold conductive strips|new_window=true] on the top of ribbon cables.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0