crwdns2933423:0crwdne2933423:0

Jura heating cartridge replacement

crwdns2933809:0crwdne2933809:0

crwdns2935433:0crwdne2935433:0

Jura Impressa opening procedure

crwdns2935443:0crwdne2935443:0

= crwdns2915112:0crwdne2915112:0 = crwdns2861241:0crwdne2861241:0
crwdns2936319:0crwdne2936319:0
crwdns2936315:0crwdne2936315:0

      crwdns2931349:0crwdne2931349:0

      crwdns2936071:01crwdne2936071:0

      The heating cartridge is the aluminum cylinder under the right side, around which spirals the heating runs. It is bolted to a plastic slide. The next steps will show how to pull out the slide and remove all connections.

      crwdns2936071:02crwdne2936071:0

      The pressure hoses are secured against slipping out with metal clips. Pull out the metal clamp on the hose between the pump and the heating cartridge

      crwdns2936071:03crwdne2936071:0

      The carriage of the heating cartridge is held with two black plastic frames. Press it up with a screwdriver until the carriage comes free.

      crwdns2936071:04crwdne2936071:0

      In this step, you must disconnect the connection between the steam knob and the steam valve. The button has two pins stuck in a round plate with a cruciform incision. The steam valve also has two pins which engage in this plate from the other side.

      crwdns2936071:05crwdne2936071:0

      The microswitch is held in place by a black plastic fabric. Push the catch to the left and lift the microswitch out. The cables can stay connected.

      crwdns2936071:06crwdne2936071:0

      Pull out the clamp on the pressure hose that comes out of the outlet valve.

      crwdns2936071:07crwdne2936071:0

      Now pull out the carriage with the heating cartridge completely and put it on the work table.

      crwdns2936071:08crwdne2936071:0

      Pull the clamp on the hose to the steam outlet.

      crwdns2936071:09crwdne2936071:0

      The yellow-green grounding cable is attached with a Phillips screw. Turn it out and disconnect the cable.

      crwdns2936071:010crwdne2936071:0

      Remove the cable lug with the blue cable from the heater.

      crwdns2936071:011crwdne2936071:0

      The temperature sensor is fastened with a holding plate and a Torx 20 screw.

      crwdns2936071:012crwdne2936071:0

      There is a thermal fuse on the gray cable between the heater and the pump. It is attached to the heating cartridge with a retaining plate.

      crwdns2936071:013crwdne2936071:0

      The heating cartridge is free.

      crwdns2936071:014crwdne2936071:0

      Turn out the long Torx 20 screw on the top of the steam valve.

      crwdns2936071:015crwdne2936071:0

      When the steam valve is removed, you can finally replace the sled. To do this, turn out three Torx 20 screws.

      crwdns2936071:016crwdne2936071:0

      The clamp for the rotary knob on the steam valve is fastened with a Torx 15 screw. Unscrew it, remove the clamp and transfer it to the new part, if necessary.

      crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0