crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Sostituzione schermo Motorola Moto Z2 Force

crwdns2935443:0crwdne2935443:0

= crwdns2915112:0crwdne2915112:0 = crwdns2861241:0crwdne2861241:0
crwdns2936315:0crwdne2936315:0
crwdns2936321:0crwdne2936321:0
Screen Assembly
Motorola Moto Z2 Force ScreenDisplay and Fingerprint Sensor Replacement
    If your Moto Z2 Force screen is cracked or not operating correctly, use this guide for the steps to replace it.
    Use this guide to remove or replace the screen and fingerprint sensor on your Motorola Moto Z2 Force. The fingerprint sensor on the Z2 Force is very difficult to remove from the screen assembly, so if you need to replace it, we suggest replacing the entire screen assembly.
    Before you begin, download the [link|https://www.motorola.com/us/rescue-and-smart-assistant/p|Rescue and Smart Assistant|new_window=true] app to backup your device and diagnose whether your problem is software or hardware related.
    ***For your safety, discharge your battery below 25% before disassembling your phone.*** This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair. If your battery is swollen, [[What to do with a swollen battery|take appropriate precautions|new_window=true]].
      To reassemble your device, follow these instructions in reverse order.
      Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.
      '''To reassemble your device, follow the above steps in reverse order.'''
      Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
      Repair didn’t go as planned? Check out our [https://www.ifixit.com/Answers/Device/Motorola%20Moto%20Z2%20Force|Answers Community] for troubleshooting help.

      crwdns2931349:0crwdne2931349:0

      crwdns2936071:01crwdne2936071:0

      Usando l'estremità piatta dello spudger in nylon, tira via il nastro adesivo nero disposto sopra il connettore dello schermo a cui è attaccato il nastro nero.

      crwdns2936071:02crwdne2936071:0

      Incunea lo strumento di apertura in plastica nella fessura creata dalla separazione tra schermo e scocca nell'angolo inferiore destro per tenerlo aperto.

      crwdns2936071:03crwdne2936071:0

      crwdns2936071:04crwdne2936071:0

      Inserisci lo spudger al di sotto del blocco del sistema di ritenuta che collega il nastro nero dello schermo alla scocca.

      crwdns2936071:05crwdne2936071:0

      Rimuovi lo schermo alzandolo da destra e facendo perno sul bordo sinistro; disponi lo schermo a faccia in giù a fianco della scocca del dispositivo.

      crwdns2936071:06crwdne2936071:0

      crwdns2936071:07crwdne2936071:0

      crwdns2936071:08crwdne2936071:0

      crwdns2936071:09crwdne2936071:0

      crwdns2936071:010crwdne2936071:0

      crwdns2936071:011crwdne2936071:0

      crwdns2936071:012crwdne2936071:0

      crwdns2936071:013crwdne2936071:0

      crwdns2936071:014crwdne2936071:0

      crwdns2936071:015crwdne2936071:0

      crwdns2936071:016crwdne2936071:0

      crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0