crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Sostituire lo schermo di un Google Pixel 2

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:02crwdnd2931529:0crwdne2931529:0

crwdns2935423:0crwdne2935423:0

crwdns2935425:01crwdne2935425:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936321:0crwdne2936321:0
crwdns2931653:01crwdne2931653:0
How to Replace a Google Pixel 2 Screen: crwdns2935265:00crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 How to Replace a Google Pixel 2 Screen: crwdns2935265:00crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

  • If your replacement display did not come with pre-installed speaker grilles or a front-facing camera bracket, carefully remove these parts from your old display. Follow the rest of the guide to install them on a new display.

  • To remove the camera bracket, apply heat, then use a thin metal blade to pry the bracket away from the old screen.

  • There are two layers that make up the speaker grille—the metal mesh grille, and a layer of thin fabric mesh behind it. Use tweezers to peel both layers off of the old screen together. Do your best to not separate those layers at all.

  • Make sure to install the grilles and gasket before applying display adhesive.

  • Cut two corners of a pre-cut adhesive card so that each side is no more than 12 mm (0.5 inches) long, or cut four 12 mm (0.5 inches) strips of double-sided adhesive.

  • The adhesive strips should be no wider than 1 mm.

  • Apply the adhesive strips to the edges of the flat side of the front-facing camera bracket. When you're done, there should be adhesive on all four edges of the camera bracket.

  • Gently press the adhesive into place using your finger or a spudger.

Se il tuo display di ricambio non è dotato di griglie degli altoparlanti installate o del supporto della fotocamera anteriore, rimuovi con attenzione queste parti dal tuo vecchio schermo. Segui la parte restante della guida per installarle sul display nuovo.

Per rimuovere il supporto della fotocamera, applica del calore e poi usa una sottile lama metallica per far leva e staccare la staffa dal vecchio schermo.

La griglia dell'altoparlante è composta da due strati: la griglia metallica e una parte sottostante di sottile tessuto spugnoso. Usa delle pinzette per staccare in un blocco solo i due strati dal vecchio schermo. Fai del tuo meglio per non separarli durante l'operazione.

Prima di applicare l'adesivo dello schermo, ricordati di installare le griglie e la guarnizione.

Taglia due angoli di un foglio adesivo pretagliato in modo che ognuno dei lati sia lungo meno di 12 mm, oppure taglia quattro strisce di biadesivo da 12 mm.

Le strisce adesive dovrebbero essere larghe al massimo 1 mm.

Applica le strisce adesive ai bordi della faccia piatta della staffa della fotocamera anteriore. Alla fine, dovrebbe esserci dell'adesivo su tutti i quattro bordi del supporto della fotocamera.

Premi delicatamente l'adesivo nella sua posizione con un dito o uno spudger.

[* icon_note] If your replacement display did not come with pre-installed speaker grilles or a front-facing camera bracket, carefully remove these parts from your old display. Follow the rest of the guide to install them on a new display.
[* black] To remove the camera bracket, apply heat, then use a thin metal blade to pry the bracket away from the old screen.
- [* black] [https://d3nevzfk7ii3be.cloudfront.net/igi/6wiDS1iavbCWpVgq.full|There are two layers that make up the speaker grille|new_window=true]—the metal mesh grille, and a layer of thin fabric mesh behind it. Use tweezers to peel both layers off of the old screen together. Do your best to not separate those layers at all.
+ [* black] [https://d3nevzfk7ii3be.cloudfront.net/igi/6wiDS1iavbCWpVgq.full|There are two layers that make up the speaker grille|new_window=true]—the metal mesh grille, and a layer of thin fabric mesh behind it. Use [product|IF145-020|tweezers] to peel both layers off of the old screen together. Do your best to not separate those layers at all.
[* icon_note] Make sure to install the grilles and gasket before applying display adhesive.
[* black] Cut two [guide|113604|corners of a pre-cut adhesive card|stepid=217050|new_window=true] so that each side is no more than 12 mm (0.5 inches) long, or cut four 12 mm (0.5 inches) strips of double-sided adhesive.
[* icon_note] The adhesive strips should be no wider than 1 mm.
[* black] Apply the adhesive strips to the edges of the flat side of the front-facing camera bracket. When you're done, there should be adhesive on all four edges of the camera bracket.
[* black] Gently press the adhesive into place using your finger or a spudger.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0