crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0
crwdns2918538:0crwdne2918538:0

Vanmoof Electrified S2 Rear Hub Upgrade

crwdns2935359:0crwdne2935359:0

  • 1 × Multi-size spoke wrench—The one that ended up working for the vanmoof nipples was the one with the blue handle
  • 1 × Zip Ties
  • 1 × Nipple Driver—(optionally you can instead use a small flat head screw driver. This is what I did)
  • 1 × Digital Caliper—doesn't need to be digital. I picked up a $7 analog one from Home Depot
  • 1 × Measuring Tape—preferably metric if you have it. I made do with an imperial one though.
  • 1 × Cable Housing Cutters—These would be very nice to have. I instead used regular wire cutting pliers because I already owned them. It was very difficult to get the housing cut without it fraying. I did do it though so its possible
  • 1 × Tire Levers—not necessary. You can remove the tire without them (google it) but its harder and these are useful to have in your emergency kit anyways. I would recommend getting some
  • 1 × Chain Tool—You need this if you plan on changing the number of teeth on the rear sprocket by more than 2 teeth
  • 1 × white paint pen
  • 4 × shifter cable housing guide
  • 1 × Shifter Cable Housing—depending on what hub you chose and what shifting set up you chose, you might not need this or need something slightly different
  • 1 × Enviolo CVP Internally Geared Hub: City 36 Hole Disc Brake—You do not need this exact hub. This is just what I used. Check the article for more details on picking a hub
  • 1 × Enviolo twist shifter—Depends on your hub set up. figure out what works for your set up. This is what I used
  • 1 × Enviolo Manual CVP Hub Interface: CT%2FCO%2FTR—depends on your hub set up. figure out what works for your set up. This is what I used
  • 1 × Enviolo CVP Standard Mounting Hardware Kit: CT CO TR—depends on your hub set up. figure out what works for your set up. This is what I used
  • 1 × Enviolo Sprocket: 16 Tooth, 3/32", Flat, Nickel Plated Cog—Depends on your set up and what gear ratio range you want. (Read more about it in the article) 16T is what I felt comfortable at.
  • 2 × FW4671 Shimano Dura-Ace CS-7800 Ultegra CS-6600 10-Speed Low Spacer—This is only needed if you are using the 16T cog on the enviolo hub. Otherwise the mounting hardware comes with the correct spacers
  • 36 × DT Swiss Champion 14 Gauge Black Spokes - 2.0 x 254 mm—This is the length I used but mine were slightly short so get 1-2mm longer if you are using the exact same hub and rim
  • 1 × DT SWISS BLACK 14G 12MM BRASS NIPPLE—get correct gauge nipple for the spokes you bought. These are 14 G to match the 14 gauge spokes
  • 1 × linseed oil—You can find it at Home Depot or Lowes. Used for lubrication when building the wheel
crwdns2915442:0crwdne2915442:0

crwdns2918526:0crwdne2918526:0

crwdns2935377:0crwdne2935377:0

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0