crwdns2933423:0crwdne2933423:0

crwdns2944351:0crwdnd2944351:0Logitech G903 Battery Replacementcrwdnd2944351:0crwdne2944351:0

crwdns2933797:0Dominik Schnabelrauchcrwdnd2933797:0crwdne2933797:0

crwdns2936043:0crwdne2936043:0 crwdns2933505:0crwdne2933505:0 Dominik Schnabelrauch

crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933801:0crwdne2933801:0
crwdns2866306:0crwdne2866306:0
Logitech G903
Type
replacement
Thing
Battery
Title
Logitech G903 Battery Replacement
Introduction
Use this guide to replace the battery in a Logitech G903.
If your battery is swollen, [[What to do with a swollen battery|take appropriate precautions|new_window=true]]. For your safety, ***discharge your battery below 25%*** before disassembling your device. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair.
This guide requires removing the mouse feet. If you’re planning to reuse your existing mouse feet, note that the adhesive needs to be thoroughly heated for them to be cleanly removed.
You might need replacement adhesive to reattach components when reassembling the device.
Time Required Min
crwdns2931287:025crwdne2931287:0
Time Required Max
crwdns2931287:045crwdne2931287:0
Imageid
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
Difficulty
Moderate
Conclusion
If possible, turn on your device and test your repair before installing new adhesive and resealing.
Secure the new battery with pre-cut adhesive or double-sided adhesive tape. In order to position it correctly, apply the new adhesive into the device at the places where the old adhesive was located, not directly onto the battery. Press the new battery firmly into place.
Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.
For optimal performance, ***calibrate your newly installed battery***: Charge it to 100% and keep charging it for at least 2 more hours. Then use your device until it shuts off due to low battery. Finally, charge it uninterrupted to 100%.
***To reassemble your device, follow the above steps in reverse order.***
Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
Repair didn’t go as planned? Check out our [link|https://www.ifixit.com/Answers|Answers community] for troubleshooting help.
Author
Public
crwdns2853046:0crwdne2853046:0

crwdns2933809:0crwdne2933809:0

crwdns2943215:0crwdne2943215:0

  • Phillips #00 Screwdriver x1 added.
  • ESD Safe Blunt Nose Tweezers x1 added.
  • iOpener x1 added.
  • Isopropyl Alcohol 70% x1 added.
  • iFixit Opening Picks (Set of 6) x1 added.
  • Spudger x1 added.
  • Microfiber Cleaning Cloths x1 added.

crwdns2935255:0crwdne2935255:0

  • In Progress added.
  • Featured Guide added.

crwdns2933623:0crwdne2933623:0

crwdns2933815:01crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:02crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0