crwdns2933423:0crwdne2933423:0

crwdns2944351:0crwdnd2944351:0ZPrinter 650 Mainboard Replacementcrwdnd2944351:0crwdne2944351:0

crwdns2933797:0Pavel Hanakcrwdnd2933797:0crwdne2933797:0

crwdns2936043:0crwdne2936043:0 crwdns2933505:0crwdne2933505:0 Pavel Hanak

crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933801:0crwdne2933801:0
crwdns2866306:0crwdne2866306:0
ZPrinter 650
Type
replacement
Thing
Mainboard
Title
ZPrinter 650 Mainboard Replacement
Introduction
The ZPrinter 650 color powder 3D printer has a large electronics module which is somewhat prone to failures. Replacement module is very expensive, it cost around 6000 USD in 2015. What is even worse, the original producer (Z Corporation) was bought out by 3D Systems and they stopped providing spare parts for older (pre-2012) printers. However, I figured out the main reason why the electronic modules fail: a small embedded PC mainboard based on VIA C3 processor. Chinese comrades who manufactured the board used a bit too cheap CPU fan and when it stops working, the CPU will burn out. In one instance, the fan started to fail after mere 2 months! You can't replace the CPU (it's soldered to the board), but it's possible to buy a new mainboard. It has part number ENDAT-3220M and can be usually found on Ebay. Ocassionally, it also appears in PC surplus stores and the like, just Google for it. Other Z Corporation printers also use this mainboard, Zprinter 450 and Zprinter 250 for example. Unfortunately, it also depends on production year of the printer, so I recommend to disassemble the printer and check the actual mainboard type before you buy.
WARNING! This repair should be performed only by skilled technician with background in electronics and/or computer service work. Moreover, it includes manipulation with very sensitive electronic components and ESD precautions must be observed during most steps!
Time Required Min
crwdns2931291:02crwdne2931291:0
Time Required Max
crwdns2931291:02crwdne2931291:0
Imageid
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
Difficulty
Difficult
Conclusion
After that, you should turn off the printer, disconnect all cables and put back cover on the electronics module. That completes the repair.
Author
Public
crwdns2853046:0crwdne2853046:0

crwdns2943215:0crwdne2943215:0

  • Phillips #1 Screwdriver x1 added.
  • PS/2 keyboard x1 added.
  • PC monitor with VGA input x1 added.
  • ESD Gloves or Bracelet x1 added.

crwdns2943213:0crwdne2943213:0

  • ENDAT-3220M mainboard x1 added.
  • High quality 40x40x10 mm 3-pin PC fan x1 added.
  • CR2032 battery x1 added.

crwdns2935255:0crwdne2935255:0

  • In Progress added.
  • Community-Contributed Guide added.

crwdns2933623:0crwdne2933623:0

crwdns2933815:01crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:02crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:03crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:04crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:05crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:06crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:07crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:08crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:09crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:010crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:011crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:012crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0