PSP 2000 Memory Stick Slot Replacement

crwdns2931653:01crwdne2931653:0 Battery




• Place PSP face down, so that the UMD Drive is facing upwards.
• Locate the battery door and open.
• Remove the battery from inside.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0 Front Casing

• This step requires the removal of the warranty sticker. Removing the sticker will void the warranty. According to the FTC removing this will not void your warranty.
• Locate the sticker in the battery compartment labeled: "En: Warranty Void if Seal Damaged."
• Remove the sticker using the PSP Opening Tools.
• Under the sticker is a 5mm Phillips screw needed in the next step.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0
• Remove four 5 mm Phillips from the case.
• If the screws stick in the case, you can use a magnetized screwdriver to draw them out.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0
• Remove the following screws from around the bezel:
• Two 4 mm Phillips
• One 5 mm Phillips
• The two shorter 4 mm screws are on the top of the PSP; the longer 5 mm screw is on the bottom.
crwdns2913378:0crwdne2913378:0
crwdns2947430:01crwdne2947430:0
crwdns2934285:0crwdne2934285:0
Beware that some models of PSP 2000 (mine is a limited edition Crisis Core FF7 silver version, so I suppose it is related to it being a japanese PSP) have 2 minute TORX screws (T1? T2?) instead of the 2x 4mm Phillips pointed in orange around the USB port.
Mighty Sashiman - Mud 3, 2020 crwdns2934203:0crwdne2934203:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0
• Gently pry the front bezel away from the casing using a PSP opening tool.
• Start on the right hand side of the PSP bezel, and carefully work the tool around the side.
• If you want to clean the control buttons or D-pad, you can easily pop them out once the faceplate is off and wipe them clean.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0 Display
• Remove the home bar by gently prying on the left and right sides of it with the opening tools. Lift the bar out of the device.
• A ribbon cable connects the home bar to the logic board. Be careful not to damage the cable when removing the bar.
crwdns2913378:0crwdne2913378:0
crwdns2947430:01crwdne2947430:0
crwdns2934285:0crwdne2934285:0
Theres a latch you have to pry on the other side of the console through the small hole in order to remove home menu bar
Janus Golovka - Mha 3, 2024 crwdns2934203:0crwdne2934203:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:07crwdne2931653:0
• With the home bar out of the way, gently pry up the display using the opening tools.
• There is another ribbon cable attached to the bottom of the LCD. Be careful not to damage either of the connectors when removing.
• Lift the black tabs of the ribbon cable connectors using a opening tool. Pull the ribbons out towards the bottom of the PSP to disconnect.
• Gently lift out the display.
crwdns2913378:0crwdne2913378:0
crwdns2935263:02crwdne2935263:0
crwdns2934285:0crwdne2934285:0
There are 2 ribbons connected to the screen. Both of them have to be disconnected in order to remove the screen.
Ovismue Veholkin - Huk 2, 2022 crwdns2934203:0crwdne2934203:0
Do not lift the black tab on the thin cable. That's attached to the logic board.
Colin Wack - Maw 2, 2024 crwdns2934203:0crwdne2934203:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:08crwdne2931653:0 Memory Stick Slot
• Remove two 4.5 mm Phillips screws from the left-hand side of the PSP.
• Slide off the left trigger along with the plastic bracket underneath.
• Carefully pry off left trigger button using opening tools.
• The button is adhered to the body. It can be re-adhered with hot glue after being pried-up, if necessary.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:09crwdne2931653:0
• Use an opening tool to lift up the brown tab on the connector and remove the cable horizontally.
• Gently remove the memory card slot by pulling it straight out.
crwdns2913378:0crwdne2913378:0
crwdns2947430:01crwdne2947430:0
crwdns2934285:0crwdne2934285:0
That's just removing the D-pad. The memory card slot is part of the main logic board.
Yomcha Go - Dzi 18, 2024 crwdns2934203:0crwdne2934203:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:08crwdnd2935293:0crwdne2935293:0

espinks

crwdns2935283:010/18/09crwdne2935283:0

3,646 crwdns2915208:0crwdne2915208:0

crwdns2935297:05crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 16

• 
• 
• 

crwdns2935301:013crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Cal Poly, Team 6-3, Maness Fall 2009 crwdns2935289:0Cal Poly, Team 6-3, Maness Fall 2009crwdne2935289:0

CPSU-MANESS-F09S6G3

crwdns2931471:05crwdne2931471:0

crwdns2935297:037crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0