crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Linear Rail V2/V3 Endstop Install

crwdns2915892:0crwdne2915892:0

CR 10 V2/V3 endstop install and adjustment.

crwdns2942213:0crwdne2942213:0

  1. Linear Rail V2/V3 Endstop Install, Linear Rail V2/V3 Endstop Install: crwdns2935265:01crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Linear Rail V2/V3 Endstop Install, Linear Rail V2/V3 Endstop Install: crwdns2935265:01crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Linear Rail V2/V3 Endstop Install, Linear Rail V2/V3 Endstop Install: crwdns2935265:01crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

    • M3 Sliding T-Nut

    • Slide in the M3 T-Nut toward the middle of the printer

    • M3X12 BHCS & M3 FLAT WASHERS

    • M3x10 FHCS

    • Adjustable Endstop Mount A

    • Adjustable Endstop Mount B

    • Tighten the M3 screw into the T-Nut

    crwdns2913378:0crwdne2913378:0

  3. Linear Rail V2/V3 Endstop Install, Endstop install: crwdns2935265:02crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Linear Rail V2/V3 Endstop Install, Endstop install: crwdns2935265:02crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Adjust endstop mount until it is square with the Linear rail

    • Remove stock endstop board form Creality mount and Reuse the stock screws to mount the endstop as shown

    crwdns2913378:0crwdne2913378:0

  4. Linear Rail V2/V3 Endstop Install, Setting endstop position: crwdns2935265:03crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Linear Rail V2/V3 Endstop Install, Setting endstop position: crwdns2935265:03crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Use M3x12 BHCS to adjust the endstop position, so the nozzle tip is even with the front edge of the bed when the end stop is triggered

    • Check the clearance between the motor and the linear adaptor. When the bed is all the way back against the endstop. There should be a 1-2 mm gap when the endstop is triggered.

    crwdns2913378:0crwdne2913378:0
crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:02crwdnd2935293:0crwdne2935293:0

AJ Pereira

crwdns2935283:005/29/20crwdne2935283:0

2,707 crwdns2915208:0crwdne2915208:0

crwdns2935297:016crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 9

crwdns2935301:06crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Tiny Machines 3D crwdns2935289:0Tiny Machines 3Dcrwdne2935289:0

Community

crwdns2931471:05crwdne2931471:0

crwdns2935297:041crwdne2935297:0

crwdns2947412:00crwdne2947412:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 1

crwdns2936753:07crwdne2936753:0 16

crwdns2936753:030crwdne2936753:0 71

crwdns2942667:0crwdne2942667:0 1,333