crwdns2894164:0crwdne2894164:0

crwdns2915892:0crwdne2915892:0

Use this guide to replace the battery in your Huawei P9 smartphone.

Before disassembling your phone, discharge the battery below 25%. The battery can catch fire and/or explode if accidentally punctured, but the chances of that happening are much lower if discharged.

  1. Huawei P9 Battery Replacement, Back Cover: step 1, image 1 of 3 Huawei P9 Battery Replacement, Back Cover: step 1, image 2 of 3 Huawei P9 Battery Replacement, Back Cover: step 1, image 3 of 3
    • First switch off your phone and remove the SIM card tray.

    • Unscrew the two Pentalobe P2 screws located at the bottom next to the device's USB C port.

    • If the screen is cracked you might want to use some tape to protect your eyes from glass shreds and get a better grip to open the phone.

  2. Huawei P9 Battery Replacement: step 2, image 1 of 2 Huawei P9 Battery Replacement: step 2, image 2 of 2
    • Avoid to lift only the display instead of the whole phone assembly as doing so may cause damage to the screen.

    • Use an iSclack or a suction handle to separate the phone assembly from the rear panel.

    • In case you can‘t manage to lift the phone assembly out of the rear panel you can insert the pointed end of a spudger in the headphone jack opening and press the phone assembly upwards until you create a gap between assembly and rear panel. Then use the spudger to lever the phone assembly out of the panel.

    • Don't remove the rear panel completely yet. There is a cable connected to it! It is running from the finger print sensor to the display unit.

  3. Huawei P9 Battery Replacement, Fingerprint sensor: step 3, image 1 of 2 Huawei P9 Battery Replacement, Fingerprint sensor: step 3, image 2 of 2
    • Disconnect the fingerprint sensor using a spudger.

  4. Huawei P9 Battery Replacement, Battery: step 4, image 1 of 3 Huawei P9 Battery Replacement, Battery: step 4, image 2 of 3 Huawei P9 Battery Replacement, Battery: step 4, image 3 of 3
    • Unplug the antenna cable.

    • Remove the sticker that sits on top of the screw.

  5. Huawei P9 Battery Replacement: step 5, image 1 of 3 Huawei P9 Battery Replacement: step 5, image 2 of 3 Huawei P9 Battery Replacement: step 5, image 3 of 3
    • Unscrew the two Phillips #00 screws that hold the metal plate in place.

    • The plate, which is covering the battery connector, has two little hooks on each side. Use a tweezer to free them and unhinge the plate by carefully moving it upwards.

  6. Huawei P9 Battery Replacement: step 6, image 1 of 2 Huawei P9 Battery Replacement: step 6, image 2 of 2
    • Now you can unplug the battery connector and bend it aside.

    • The EVA-L09 model has an NFC antenna adhered onto the battery.

    • If you are just removing the battery to get to the display, you can leave the NFC on the battery.

    • Mark its place on the battery with a felt pen for reassembly. Carefully peel it off and make sure not to rip or crease the antenna.

    • For reassembly, place the NFC antenna on the battery where it was before so its contacts align with their counterparts.

  7. Huawei P9 Battery Replacement: step 7, image 1 of 2 Huawei P9 Battery Replacement: step 7, image 2 of 2
    • Free the ends of the adhesive pull tabs to get a good grip on them.

    • The battery is secured with three pieces of adhesive, a removable pull-tab in the center, and on the SIM tray side. A third piece of adhesive on the button side has no pull-tab.

    • Pull the adhesive tabs in a slow constant movement to free the battery.

    • Should those adhesive tabs snap, you might want to use an iOpener to heat and soften them a little bit so you can pry out the battery with a spudger.

    • There are two cables running directly underneath the battery. Take care not to damage them when prying with a spudger! You can see their position in the last picture.

    • Slowly lift the battery toward the button side and free it from the remaining hidden piece of adhesive.

    • When reassembling your phone, replace old adhesive with stretch release adhesive strips, double-sided tape, or pre-cut adhesive strips.

crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2878426:086crwdne2878426:0

Tobias Isakeit

crwdns2886885:031/03/2014crwdne2886885:0

102,192 crwdns2915208:0crwdne2915208:0

crwdns2886889:0183crwdne2886889:0

crwdns2915084:0crwdne2915084:0

iFixit crwdns2886886:0iFixitcrwdne2886886:0

Community

crwdns2858115:0146crwdne2858115:0

crwdns2886889:015,629crwdne2886889:0

crwdns2917036:025crwdne2917036:0

Just FYI, My replacement battery from Huawei doesn’t fit. The cable doesn’t reach the connector. Soldering Required!

https://imgur.com/gallery/vTsX8

dallebull - crwdns2853112:0crwdne2853112:0

Bonjour j es effectué cette opération.J es changé le connecteur de chargeur complet suite à un dysfonctionnement. Et la batterie aussi.Et mon soucis reste le même. Le téléphone s allumé mais pas de voyant de charge.merci de me renseigner.

Berhault - crwdns2853112:0crwdne2853112:0

Bonjour,

J’ai le même problème , avez-vous trouvé une solution ?

Amenis -

Bonjour suite à une panne avec mon huawei p9 j es changé le connecteur de chargeur et la batterie et mon problèmereste toujours le même. Il charge toujours pas.merci de me

Berhault - crwdns2853112:0crwdne2853112:0

Dalebull what the !&&* have you done to the batteries in the pictures

Justinas Vaiciunas - crwdns2853112:0crwdne2853112:0

crwdns2917038:0crwdne2917038:0

crwdns2894754:0crwdne2894754:0:

crwdns2894766:024crwdne2894766:0 14

crwdns2894768:07crwdne2894768:0 115

crwdns2894768:030crwdne2894768:0 440

crwdns2894770:0crwdne2894770:0 119,625