Geardup RC Ford Mustang GT Remote Circuit Board Replacement

crwdns2931653:01crwdne2931653:0 Lower Remote Control




• Remove the 5mm Phillips #0 screw from the remote control.
• Using the tab, lift the battery cover from the remote control to expose the battery.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0 Remote Circuit Board



• Unscrew the six 5mm Phillips #0 screws on the back of the remote
• Separate the back of the remote from the front panel.
• During re-assembly, make sure the plastic button covers on the front panel align with the buttons on the back panel. If they do not, the buttons may be forced into an always "pressed" state.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0
• Remove the two left and right buttons from their insets in the controller.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0
• Remove the 5mm Phillips #0 screw that connects the antennae to the circuit board.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0
• Unscrew 5mm Phillips #0 screw located at the bottom of the board in the center.
• Remove the circuit board from the casing.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0
• Make note of where each wire connects to the circuit board for re-assembly as they will be removed in the next step.
• Using the copper solder wick, remove the solder connecting the nine wires to the circuit board.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:03crwdnd2935293:0crwdne2935293:0

Jake Stone

crwdns2935283:002/01/15crwdne2935283:0

611 crwdns2915208:0crwdne2915208:0

crwdns2935297:04crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 12

• 
• 
• 

crwdns2935301:09crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Cal Poly, Team 8-38, Amido Winter 2015 crwdns2935289:0Cal Poly, Team 8-38, Amido Winter 2015crwdne2935289:0

CPSU-AMIDO-W15S8G38

crwdns2931471:04crwdne2931471:0

crwdns2935297:08crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0