Epomaker Shadow-X PCB Replacement

crwdns2944107:0crwdnd2944107:0Beck Spitlercrwdnd2944107:0crwdnd2944107:0crwdnd2944107:03crwdnd2944107:0crwdne2944107:0

crwdns2944111:0January 2, 2025crwdne2944111:0

15 - 20 crwdns2931279:0crwdne2931279:0

crwdns2937801:0crwdne2937801:0

crwdns2915892:0crwdne2915892:0

The Printed Circuit Board (PCB) is a critical part of the keyboard, responsible for registering key presses and controlling LED functionality. Replacing the PCB may be necessary if there are issues with key registration or other electrical problems. Follow this guide to safely replace the PCB in your Epomaker Shadow-X.

crwdns2942213:0crwdne2942213:0

crwdns2943215:0crwdne2943215:0

crwdns2944105:0crwdne2944105:0

crwdns2931653:01crwdne2931653:0 PCB

Epomaker Shadow-X PCB Replacement, PCB: crwdns2935265:01crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

Power off the keyboard and unplug any attached cables.
Place the keyboard on a clean, static-free workspace and wear an anti-static wrist strap if available.

crwdns2913378:0crwdne2913378:0

crwdns2931653:02crwdne2931653:0

Epomaker Shadow-X PCB Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:03crwdne2935265:0

Epomaker Shadow-X PCB Replacement: crwdns2935265:02crwdnd2935265:02crwdnd2935265:03crwdne2935265:0

Epomaker Shadow-X PCB Replacement: crwdns2935265:02crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

Use a keycap puller to remove all keycaps from the keyboard.
Remove all eight of the hex screws that secure the lower case.
Remove the lower case.

crwdns2913378:0crwdne2913378:0

crwdns2931653:03crwdne2931653:0

Epomaker Shadow-X PCB Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

Locate the PCB, which is mounted below the switch plate.
Disconnect any cables or connectors between the PCB and other components
Remove any screws or clips securing the PCB to the keyboard case. Carefully lift the PCB out of the case.
If there is adhesive or sticky residue holding it, gently work around the edges to release it without damaging components.

crwdns2913378:0crwdne2913378:0

crwdns2931653:04crwdne2931653:0

Epomaker Shadow-X PCB Replacement: crwdns2935265:04crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

Place the new PCB into the same position in the case, aligning all mounting holes and connectors.

crwdns2913378:0crwdne2913378:0

crwdns2915888:0crwdne2915888:0

To reassemble your device, follow the above steps in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting or ask our Answers community for help.