crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Repair information and guides for the Apple iPhone 5s that was announced on September 10, 2013. Model: A1533, A1453, A1457, A1528, A1530, A1518

crwdns2934591:03535crwdne2934591:0 crwdns2934593:0crwdne2934593:0

crwdns2933897:0crwdne2933897:0

iPhone 5s battery replace issues

Hello i replaced my iphone 5s battery but when start my phone battery charge status 1% when i recharge battery its jump and stuck on 27% percent

After i shutdown my phone and on it Again battery comes on 1% again are there any solutions

Also my phone randomly rebooting after 2-3 minutes

crwdns2934089:0crwdne2934089:0 crwdns2934093:0crwdne2934093:0

crwdns2934109:0crwdne2934109:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 0
crwdns2942205:01crwdne2942205:0

where did you get the battery from?

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934285:0crwdne2934285:0

crwdns2933315:02crwdne2933315:0

crwdns2934221:0crwdne2934221:0
crwdns2931211:0crwdne2931211:0 crwdns2931215:0crwdne2931215:0 crwdns2934225:0crwdne2934225:0
crwdns2934057:0crwdne2934057:0

crwdns2933897:0crwdne2933897:0

So you make Battery BSI track open. See around the battery connector you can see some parts are missing. If the coil is missing simply jumper it and enjoy.

crwdns2934105:0crwdne2934105:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 1

crwdns2942205:01crwdne2942205:0:

Please explain more i not understand what you are mean

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934285:0crwdne2934285:0

crwdns2933897:0crwdne2933897:0

The symptoms your iPhone have is most likely caused by a damage logic board. Take a good look at the logic board around where the battery connector is, it is possible that you have knock of a small component of the logic board when you have replaced the battery. You might need a magnifier or microscope to see it, at the place where component is missing you can make a jumper between the two pads. Sorry for my poor English but I hope you understand what I try to explaine.

see this for example: https://youtu.be/Q4fIp9vgsB8

crwdns2934105:0crwdne2934105:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 0

crwdns2944067:02crwdne2944067:0:

Hey

Unfortunately i not have  microscope but if there's any missing  part around  battery  socket are that component repairable?

And are you think maybe  the new  battery  have a problem  i am so scared  about component if they  missing

Sorry  for  my poor  English

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

I think the problem is in a missing component around the battery connector, take a magnifier and take a look, it isn’t that difficult to make a jumper, I use silver conductive glue to make this jumper. Much easier then with micro solderen.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934285:0crwdne2934285:0

crwdns2934229:0crwdne2934229:0

Abdurrahman Najdi crwdns2934231:0crwdne2934231:0
crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 0

crwdns2936753:030crwdne2936753:0 1

crwdns2942667:0crwdne2942667:0 89