Why is my 2011 chrysler 200 heater blowing warm on one vent?

Question

Chrysler

Repair guides and support for cars and other vehicles produced by the Chrysler division of the Fiat Chrysler Automobiles US LLC.

crwdns2934591:0191crwdne2934591:0 crwdns2934593:0crwdne2934593:0

Billie s. @chrysler200

crwdns2934065:0crwdne2934065:0: 25

1

crwdns2931729:0crwdne2931729:0: Sun 5, 2018

crwdns2933897:0crwdne2933897:0

Why is my 2011 chrysler 200 heater blowing warm on one vent?

2011 chrysler 200 my heater is only blowing warm out of the drivers vent only. The rest are blowing cold. it is Not dual climate, it is a single climate control. the defrost, floor well all of it blows cold but drivers vent . when it runs warm then it blows a lil bit warmer. I'm freezing in my car. Any ideas?

crwdns2934089:0crwdne2934089:0 crwdns2934093:0crwdne2934093:0

crwdns2934109:0crwdne2934109:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0

crwdns2889612:0crwdne2889612:0 2

crwdns2944067:04crwdne2944067:0:

I changed the two actuators on my Chrysler 200 and still have heat on drivers side and cold on passenger side. What else do I need to do?

crwdns2934271:0N'w 15, 2018crwdnd2934271:0 Shanna Montgomery crwdne2934271:0

We had our 2011 Chrysler taken apart at the shop last year to fix this issue . . . still does the same thing. Blows hot on driver’s side but cold on passenger. It does warm up slightly after a bit. I noticed that the water temperature gage dial stays between C and midway (at 8:00 position) except when it idles for more than 20 minutes sitting in the drive. Then, the heater works great. Almost as soon as we take off, the gage goes back to the 8:00 position and the air on the passenger side is cold again. What the heck? Please, somebody figure this out. Forum posts indicate this is a default situation on this vehicle across the board.

crwdns2934271:0Huk 8, 2019crwdnd2934271:0 jboskers crwdne2934271:0

Did anyone figure this out? My 2011 Chrysler 200 is doing the exact same thing

crwdns2934271:0N'w 20, 2020crwdnd2934271:0 alyssa.macdonald.1014 crwdne2934271:0

Do you have the trim level for individual environment control?

crwdns2934271:0Yan 23, 2021crwdnd2934271:0 who crwdne2934271:0

crwdns2934285:0crwdne2934285:0

crwdns2933315:02crwdne2933315:0

I changed the two actuators on my Chrysler 200 and still have heat on drivers side and cold on passenger side. What else do I need to do? — Shanna Montgomery
We had our 2011 Chrysler taken apart at the shop last year to fix this issue . . . still does the same thing. Blows hot on driver’s side but cold on passenger. It does warm up slightly after a bit. I noticed that the water temperature gage dial stays between C and midway (at 8:00 position) except when it idles for more than 20 minutes sitting in the drive. Then, the heater works great. Almost as soon as we take off, the gage goes back to the 8:00 position and the air on the passenger side is cold again. What the heck? Please, somebody figure this out. Forum posts indicate this is a default situation on this vehicle across the board. — jboskers
Did anyone figure this out? My 2011 Chrysler 200 is doing the exact same thing — alyssa.macdonald.1014
Do you have the trim level for individual environment control? — who