crwdns2933423:0crwdne2933423:0

Repair information for the Mophie PowerStation 5X portable charger. Model numbers: PWRSTION-10K-ALM, MOPPS10KSLVV1. Released ~2016.

crwdns2934591:04crwdne2934591:0 crwdns2934593:0crwdne2934593:0

2 x 4.5 volt units, and 1 x 9 volt DC power block

As the title says, I have two 4.5 volt LED light strips (each one originally ran off 3x1.5 AA batteries). Can I use one 9 volt AC-to-DC power supply (wall wart type) to power these?

If so, do I wire these lights in series, or parallel?

Thanks!

crwdns2934081:0crwdne2934081:0 crwdns2934083:0crwdne2934083:0 crwdns2934093:0crwdne2934093:0

crwdns2934109:0crwdne2934109:0

crwdns2889612:0crwdne2889612:0 0
crwdns2934285:0crwdne2934285:0

crwdns2933315:02crwdne2933315:0

crwdns2934051:0crwdne2934051:0

Keep your 9V AC adapter. Connect your LED strips in series. Use a resistor from your adapter to the LED strips.

You do need to know what LED's you have and how many. Typical values for LEDs are:

Red LED: 2V 15mA

Green LED: 2.1V 20mA

Blue LED: 3.2V 25mA

While LED: 3.2V 25mA

To figure out the size of the resistor use R = (V1 - V2) / I

R=(9-4.5)/I

(9-4.5)/0.02

4.5/0.02=225 ohms (easiest available resistor would b a 230ohm resistor)

Or you can use this calculatorto figure out how to wire it by using resistors.

crwdns2934105:0crwdne2934105:0

crwdns2889612:0crwdne2889612:0 2

crwdns2944067:03crwdne2944067:0:

the resistor values given are quite not right.in series connection , the current through one led passes through the rest of the leds.so the current stays constant.[inthis case 20mA.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

@renre thank you and it has been corrected

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

Remember that a resistor will dissipate some power, perhaps as much as your LED strip [constant 20mA current x (9-4.5)V=90mW; 1/8W should be fine] so always check the power rating of a resistor before finishing your design.

It's worth trying both strips in series, (+)-[strip]-(-)(+)-[strip]-(-); if they have some internal current regulation, you may not need more at all.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934285:0crwdne2934285:0

Connection will be in series

crwdns2934105:0crwdne2934105:0

crwdns2889612:0crwdne2889612:0 1

crwdns2944067:02crwdne2944067:0:

Would you anticipate problems doing this? Would it be better to use TWO separate power supplies, 4.5 volts each?

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

No as long as you connect in the series no problems ..... resistance = V/Amps if you want can add a resistor , considering current 40ma for 2 led strips ....

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934285:0crwdne2934285:0

crwdns2934229:0crwdne2934229:0

Nicholas Kormanik crwdns2934231:0crwdne2934231:0
crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 1

crwdns2936753:07crwdne2936753:0 8

crwdns2936753:030crwdne2936753:0 19

crwdns2942667:0crwdne2942667:0 754