crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0
crwdns2947577:0crwdnd2947577:0crwdne2947577:0

Repair guides, disassembly information, and troubleshooting for the Logitech DRIVING FORCE SHIFTER (released 2015).

crwdns2947272:01crwdne2947272:0 crwdns2915696:0crwdne2915696:0

crwdns2933897:0crwdne2933897:0

make this into usb

So i just bought an logitech Driving force Shifter, and want to make a standalone version, cause i dont have the wheel for it, and i figured they use SUBD9 Connector, well only one, and i hoped to get some help from anyone, that could help me make this happen to become a usb connector?

i have an arduino i could use to convert the SUBD to the usb through arduino

i watched this guy here but still yet i didnt get much out of it..

crwdns2934089:0crwdne2934089:0 crwdns2934093:0crwdne2934093:0

crwdns2934109:0crwdne2934109:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 0
crwdns2944067:04crwdne2944067:0

I doubt you could do that.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

well @pccheese haha lets hope i eventually will come up with something :) :P

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

Good luck! You'll need it. Not only will you have to adapt the connector, but you will have change the firmware to accept this new interface.

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

http://www.leobodnar.com/shop/index.php?...

crwdns2934271:0crwdnd2934271:0crwdne2934271:0

crwdns2934285:0crwdne2934285:0

crwdns2933315:02crwdne2933315:0

crwdns2934221:0crwdne2934221:0
crwdns2931211:0crwdne2931211:0 crwdns2931215:0crwdne2931215:0 crwdns2934225:0crwdne2934225:0
crwdns2934057:0crwdne2934057:0

crwdns2933897:0crwdne2933897:0

You are correct. Logitech says that the shifter connector is a DB-9 Male.

So maybe this will work?

https://www.ebay.com/itm/8-Inch-0-25m-RS...

crwdns2934105:0crwdne2934105:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 2
crwdns2934285:0crwdne2934285:0

crwdns2933897:0crwdne2933897:0

Nothing but a new usb controller will work , the shifter is only a axis with the mechanism, nothing else , no board, no chips, you need a Arduino to map the axis coordinates into buttons in order to work

crwdns2934105:0crwdne2934105:0

crwdns2853045:0crwdne2853045:0 crwdns2853046:0crwdne2853046:0
crwdns2889612:0crwdne2889612:0 0
crwdns2934285:0crwdne2934285:0

crwdns2934229:0crwdne2934229:0

Petter Berget crwdns2934231:0crwdne2934231:0
crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 1

crwdns2936753:07crwdne2936753:0 7

crwdns2936753:030crwdne2936753:0 17

crwdns2942667:0crwdne2942667:0 3,443