crwdns2933423:0crwdne2933423:0
crwdns2918538:0crwdne2918538:0

crwdns2934243:0crwdne2934243:0 Nick

crwdns2934249:0crwdne2934249:0:

-I would check the back cover as a lot of printers use a special rear cover for duplexing - the exception is 110lb+ printers with duplex support that require active duplexing like the MS8 and MS9 series, as well as the subsequent CS versions. Check for things like stripped gears or a loose panel, to start - if you do not see anything obvious, you may have a bad duplex assembly. Here is a link to the SM: https://www.laserexpressinc.com/manuals/Brother/brother-dcp-9030cdn-l3510cdw-l3517cdw-l3550cdw-l3551cdw-hl-l3290cdw-mfc-9150cdn-9350cdw-l3710cw-l3730cdn-l3735cdn-l3745cdw-l3750cdw-l3770cdw-service-manual.pdf
+I would check the back cover, as a lot of printers use a special rear cover for duplexing - the exception is 110 lb+ printers with duplex support that require active duplexing like the MS8 and MS9 series, as well as the subsequent CS versions. Check for things like stripped gears or a loose panel, to start - if you do not see anything obvious, you may have a bad duplex assembly or a damaged paper eject. Here is a link to the SM: https://www.laserexpressinc.com/manuals/Brother/brother-dcp-9030cdn-l3510cdw-l3517cdw-l3550cdw-l3551cdw-hl-l3290cdw-mfc-9150cdn-9350cdw-l3710cw-l3730cdn-l3735cdn-l3745cdw-l3750cdw-l3770cdw-service-manual.pdf
[document|42148]
It's deep in there on this one :-(. Not a quick job to replace. That said outside of the large commercial tier printers like the MS8 and a lot of the higher end CS units, this is normal - most consumer printers aren't built such that you can pull the duplexer out in 5-10 minutes and replace it.

crwdns2915684:0crwdne2915684:0:

open

crwdns2934245:0crwdne2934245:0 Nick

crwdns2934249:0crwdne2934249:0:

I would check the back cover as a lot of printers use a special rear cover for duplexing - the exception is 110lb+ printers with duplex support that require active duplexing like the MS8 and MS9 series, as well as the subsequent CS versions. Check for things like stripped gears or a loose panel, to start - if you do not see anything obvious, you may have a bad duplex assembly. Here is a link to the SM: https://www.laserexpressinc.com/manuals/Brother/brother-dcp-9030cdn-l3510cdw-l3517cdw-l3550cdw-l3551cdw-hl-l3290cdw-mfc-9150cdn-9350cdw-l3710cw-l3730cdn-l3735cdn-l3745cdw-l3750cdw-l3770cdw-service-manual.pdf
[document|42148]
-It's deep in there on this one :-(. Not a quick job to replace.
+It's deep in there on this one :-(. Not a quick job to replace. That said outside of the large commercial tier printers like the MS8 and a lot of the higher end CS units, this is normal - most consumer printers aren't built such that you can pull the duplexer out in 5-10 minutes and replace it.

crwdns2915684:0crwdne2915684:0:

open

crwdns2934241:0crwdne2934241:0 Nick

crwdns2934249:0crwdne2934249:0:

I would check the back cover as a lot of printers use a special rear cover for duplexing - the exception is 110lb+ printers with duplex support that require active duplexing like the MS8 and MS9 series, as well as the subsequent CS versions. Check for things like stripped gears or a loose panel, to start - if you do not see anything obvious, you may have a bad duplex assembly. Here is a link to the SM: https://www.laserexpressinc.com/manuals/Brother/brother-dcp-9030cdn-l3510cdw-l3517cdw-l3550cdw-l3551cdw-hl-l3290cdw-mfc-9150cdn-9350cdw-l3710cw-l3730cdn-l3735cdn-l3745cdw-l3750cdw-l3770cdw-service-manual.pdf

[document|42148]

It's deep in there on this one :-(. Not a quick job to replace.

crwdns2915684:0crwdne2915684:0:

open