My melitta caffeo barista T I can’t get the brewing unit fully in.. it slides over the wheel easily and I am able to lock the handle. But it isn’t being recognised as inserted. When it’s as far as I am able to insert it there is a small gap so the 2 small stumps don’t push the retracting pins into the roller to push the roller cover to the right. I’ve reset the cog wheel inside the machine madr sure there no dirt etc. the circle with the bump that’s has to be at 3oclock is fine. I’ve lubricated with food silicone, cooking oil after cleaning the unit. Google said to make sure the sensor is clean but I’ve no idea where that is or what it looks like. I’ve always struggled with getting it back in but this time I’ve been trying for three days now. I’m a 79 old old female don’t know the jargon for the bits and my hands are a bit arthritic . So if someone could point me in the direction of this sensor that has to be triggered to accept the unit or tell me that the stumpy things should not be visible looking through where the tray goes. If it is that then I will ask a young fellow neighbour to give i a push, I have btw had it next to a wall to push unit in and I just can’t get it any further the gap is wider than the length of the stumps. 🤞🤞🤞🤞 for any help. Hope you understand
My melitta caffeo barista T I can’t get the brewing unit fully in.. it slides over the wheel easily and I am able to lock the handle. But it isn’t being recognised as inserted. When it’s as far as I am able to insert it there is a small gap so the 2 small stumps don’t push the retracting pins into the roller to push the roller cover to the right. I’ve reset the cog wheel inside the machine madr sure there no dirt etc. the circle with the bump that’s has to be at 3oclock is fine. I’ve lubricated with food silicone, cooking oil after cleaning the unit. Google said to make sure the sensor is clean but I’ve no idea where that is or what it looks like. I’ve always struggled with getting it back in but this time I’ve been trying for three days now. I’m a 79 old old female don’t know the jargon for the bits and my hands are a bit arthritic . So if someone could point me in the direction of this sensor that has to be triggered to accept the unit or tell me that the stumpy things should not be visible looking through where the tray goes. If it is that then I will ask a young fellow neighbour to give i a push, I have btw had it next to a wall to push unit in and I just can’t get it any further the gap is wider than the length of the stumps. 🤞🤞🤞🤞 for any help. Hope you understand
My melitta caffeo barista T I can’t get the brewing unit fully in.. it slides over the wheel easily and I am able to lock the handle. But it isn’t being recognised as inserted. When it’s as far as I am able to insert it there is a small gap so the 2 small stumps don’t push the retracting pins into the roller to push the roller cover to the right. I’ve reset the cog wheel inside the machine madr sure there no dirt etc. the circle with the bump that’s has to be at 3oclock is fine. I’ve lubricated with food silicone, cooking oil after cleaning the unit. Google said to make sure the sensor is clean but I’ve no idea where that is or what it looks like. I’ve always struggled with getting it back in but this time I’ve been trying for three days now. I’m a 79 old old female don’t know the jargon for the bits and my hands are a bit arthritic . So if someone could point me in the direction of this sensor that has to be triggered to accept the unit or tell me that the stumpy things should not be visible looking through where the tray goes. If it is that then I will ask a young fellow neighbour to give i a push, I have btw had it next to a wall to push unit in and I just can’t get it any further the gap is wider than the length of the stumps. 🤞🤞🤞🤞 for any help. Hope you understand
My melitta caffeo barista T I can’t get the brewing unit fully in.. it slides over the wheel easily and I am able to lock the handle. But it isn’t being recognised as inserted. When it’s as far as I am able to insert it there is a small gap so the 2 small stumps don’t push the retracting pins into the roller to push the roller cover to the right. I’ve reset the cog wheel inside the machine madr sure there no dirt etc. the circle with the bump that’s has to be at 3oclock is fine. I’ve lubricated with food silicone, cooking oil after cleaning the unit. Google said to make sure the sensor is clean but I’ve no idea where that is or what it looks like. I’ve always struggled with getting it back in but this time I’ve been trying for three days now. I’m a 79 old old female don’t know the jargon for the bits and my hands are a bit arthritic . So if someone could point me in the direction of this sensor that has to be triggered to accept the unit or tell me that the stumpy things should not be visible looking through where the tray goes. If it is that then I will ask a young fellow neighbour to give i a push, I have btw had it next to a wall to push unit in and I just can’t get it any further the gap is wider than the length of the stumps. 🤞🤞🤞🤞 for any help. Hope you understand