I tried to find the why for more days now, and am now on my way to give up.
I have a RSH1DTMH american fridge-freezer, and have some problems on the freezer part, fridge working well after mooving the temperature sensor.
Freezer is not freezing, i can’t tell at what temerature it keeps, but certainly above 0°C because water put in stays a water.
I checked the temperature sensor with the ohm meter, and it seems OK, checked the defrost heater (manual forced defrost) - works well, and the fan inside the freezer - is OK.
I’m not sure where is the defrost thermostat, i see 2 pieces that looks similar to the thermostat I saw on some videos on youtube treating different fridges, but i’m not sure if it’s this and anyway seems more complicated to get out because the wires going out of it doesn’t go to one place.
What’s more when the fridge is turned on I can see that the freezer is trying to do something, because after few minutes you can see a lot of frost on one tube. The other thing is that temperature on the panel is getting lower to reach after a long time the temperature that I set so -19°C. It takes a long time, between half a day and one day, but finally it shows and stays at -19 but that’s not right, because the water put inside doesn’t even freeze.
Join some pictures to show what I’m trying to explain :)
Any help appreciated :) !!
[image|2220540]
[image|2220542]
[image|2220541]
=== Update (10/09/2020) ===
It went into forced operation, but it didn’t make any sound.
I mesured again the sensor while the dispaly is showing -25°C, I join the picture because I’m not sure if I did it with correct setting of ohm-meter.
[image|2226983]
here’s how it’s frosted at the moment
my estimation is that it’s around +20°C inside the freezer
[image|2226986]
+
+
=== Update (10/09/2020) ===
+
+
And here is the image of the temerature sensor
+
+
It was attached to the tube going out of the silver reservoir with a plastic attach but i took it out to be able to disconnect it totally
I tried to find the why for more days now, and am now on my way to give up.
I have a RSH1DTMH american fridge-freezer, and have some problems on the freezer part, fridge working well after mooving the temperature sensor.
Freezer is not freezing, i can’t tell at what temerature it keeps, but certainly above 0°C because water put in stays a water.
I checked the temperature sensor with the ohm meter, and it seems OK, checked the defrost heater (manual forced defrost) - works well, and the fan inside the freezer - is OK.
I’m not sure where is the defrost thermostat, i see 2 pieces that looks similar to the thermostat I saw on some videos on youtube treating different fridges, but i’m not sure if it’s this and anyway seems more complicated to get out because the wires going out of it doesn’t go to one place.
What’s more when the fridge is turned on I can see that the freezer is trying to do something, because after few minutes you can see a lot of frost on one tube. The other thing is that temperature on the panel is getting lower to reach after a long time the temperature that I set so -19°C. It takes a long time, between half a day and one day, but finally it shows and stays at -19 but that’s not right, because the water put inside doesn’t even freeze.
Join some pictures to show what I’m trying to explain :)
Any help appreciated :) !!
[image|2220540]
[image|2220542]
[image|2220541]
+
+
=== Update (10/09/2020) ===
+
+
It went into forced operation, but it didn’t make any sound.
+
+
I mesured again the sensor while the dispaly is showing -25°C, I join the picture because I’m not sure if I did it with correct setting of ohm-meter.
+
+
[image|2226983]
+
+
here’s how it’s frosted at the moment
+
+
my estimation is that it’s around +20°C inside the freezer
Hi everybody :)
I tried to find the why for more days now, and am now on my way to give up.
I have a RSH1DTMH american fridge-freezer, and have some problems on the freezer part, fridge working well after mooving the temperature sensor.
Freezer is not freezing, i can’t tell at what temerature it keeps, but certainly above 0°C because water put in stays a water.
I checked the temperature sensor with the ohm meter, and it seems OK, checked the defrost heater (manual forced defrost) - works well, and the fan inside the freezer - is OK.
I’m not sure where is the defrost thermostat, i see 2 pieces that looks similar to the thermostat I saw on some videos on youtube treating different fridges, but i’m not sure if it’s this and anyway seems more complicated to get out because the wires going out of it doesn’t go to one place.
What’s more when the fridge is turned on I can see that the freezer is trying to do something, because after few minutes you can see a lot of frost on one tube. The other thing is that temperature on the panel is getting lower to reach after a long time the temperature that I set so -19°C. It takes a long time, between half a day and one day, but finally it shows and stays at -19 but that’s not right, because the water put inside doesn’t even freeze.
Join some pictures to show what I’m trying to explain :)
Any help appreciated :) !!
[image|2220540]
[image|2220542]
[image|2220541]