I dropped my Early 2009 MacBook Pro (don’t ask)
The case on the back of the screen seems to have come unglued at one corner. When I close the screen one corner doesn’t sit flush. You can lift the flap up enough to see the glue that was meant to be holding it together. Is there a way of re-glueing this back? Or any other suggestions?
=== Update ===
As you can see the screen is fine, still attached to computer, but the actual case or shell of it has come away.
When I pry it open a little it is possible to see where the glue was which stuck it down. Do you think I should try to glue it back? When I squeeze the lid down gently it fits back into place. If I were to glue it back is there a special glue I should use? A heat resistant one?
cheers
[image|25581]
[image|25583]
[image|25582]
I dropped my Early 2009 MacBook Pro (don’t ask)
The case on the back of the screen seems to have come unglued at one corner. When I close the screen one corner doesn’t sit flush. You can lift the flap up enough to see the glue that was meant to be holding it together. Is there a way of re-glueing this back? Or any other suggestions?
=== Update ===
As you can see the screen is fine, still attached to computer, but the actual case or shell of it has come away.
When I pry it open a little it is possible to see where the glue was which stuck it down. Do you think I should try to glue it back? When I squeeze the lid down gently it fits back into place. If I were to glue it back is there a special glue I should use? A heat resistant one?
cheers
[image|25581]
[image|25583]
[image|25582]
I dropped my Early 2009 MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?
+
I dropped my Early 2009 MacBook Pro (don’t ask)
-
== Updates ==
+
The case on the back of the screen seems to have come unglued at one corner. When I close the screen one corner doesn’t sit flush. You can lift the flap up enough to see the glue that was meant to be holding it together. Is there a way of re-glueing this back? Or any other suggestions?
-
as you can seethe screen is fine, still attached to computer, but the actual case or shell of it has come away. when i prize it open a little it is possible to see where the glue was which stuck it down. do you think i should try to glue it back? when i squeeze the lid down gently it fits back into place. if i were to glue it back is there a special glue i should use? a heat resistant one?
+
=== Update ===
+
+
As you can see the screen is fine, still attached to computer, but the actual case or shell of it has come away.
+
+
When I pry it open a little it is possible to see where the glue was which stuck it down. Do you think I should try to glue it back? When I squeeze the lid down gently it fits back into place. If I were to glue it back is there a special glue I should use? A heat resistant one?
I dropped my Early 2009 MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?
== Updates ==
as you can seethe screen is fine, still attached to computer, but the actual case or shell of it has come away. when i prize it open a little it is possible to see where the glue was which stuck it down. do you think i should try to glue it back? when i squeeze the lid down gently it fits back into place. if i were to glue it back is there a special glue i should use? a heat resistant one?
I dropped my Early 2009 MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?
== Updates ==
+
+
as you can seethe screen is fine, still attached to computer, but the actual case or shell of it has come away. when i prize it open a little it is possible to see where the glue was which stuck it down. do you think i should try to glue it back? when i squeeze the lid down gently it fits back into place. if i were to glue it back is there a special glue i should use? a heat resistant one?
i dropped my Early 2009 MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?
+
I dropped my Early 2009 MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?
i dropped my Early 2009 MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?
i dropped my MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?
+
i dropped my Early 2009 MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?
i dropped my MBP (dont ask) and the case on the back of the screen seems to have come unglued at one corner. when i close the screen one corner doesnt sit flush. you can lift the flap up enough to see the glue that was meant to be holding it together. is there a way of re-glueing this back? or any other suggestions?