crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Moodo Smart Aroma Diffuser Teardown

crwdns2935163:0crwdne2935163:0 Markus (crwdns2935085:0crwdne2935085:0)
crwdns2935165:0October 16, 2020crwdne2935165:0
  • crwdns2935167:0crwdne2935167:0 0
  • crwdns2935169:0crwdne2935169:0 0
  • crwdns2935171:0crwdne2935171:0 766

Moodo Smart Aroma Diffuser Teardown

crwdns2935163:0crwdne2935163:0 Markus (crwdns2935085:0crwdne2935085:0)
crwdns2935165:0October 16, 2020crwdne2935165:0
  • crwdns2935167:0crwdne2935167:0 0
  • crwdns2935169:0crwdne2935169:0 0
  • crwdns2935171:0crwdne2935171:0 766

crwdns2918522:0crwdne2918522:0

crwdns2915892:0crwdne2915892:0

Having a look into the Moodo Smart Aroma Diffuser.
You can also use this as a guide to replace a fan.

crwdns2942213:0crwdne2942213:0

crwdns2935311:0crwdnd2935311:0crwdne2935311:0 crwdns2935313:0Moodo Smart Aroma Diffusercrwdnd2935313:0crwdnd2935313:0crwdne2935313:0

  1. Moodo Smart Aroma Diffuser Teardown, Device: crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Moodo Smart Aroma Diffuser Teardown, Device: crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • The device can be opened by removing the 4 Philips screws visible from the bottom

    crwdns2913378:0crwdne2913378:0

  3. Moodo Smart Aroma Diffuser Teardown, Fan assembly: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • The fan and air guidance assembly is attached to the main PCB with 2 screws.

    • Each fan has one connector for power and one for the pod sensor - these need to be disconnected from the PCB before removing the fan assembly. If you want to replace a fan, you will need to unhook the sensor cables from the sides.

    • Fans used are: 1604KL-01W-B39-B00 NMB Technologies DC Fans DC Axial Fan, 40x10mm, 5VDC, 4.2CFM

    crwdns2913378:0crwdne2913378:0

  4. Moodo Smart Aroma Diffuser Teardown, PCB: crwdns2935265:03crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Moodo Smart Aroma Diffuser Teardown, PCB: crwdns2935265:03crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • The main PCB connects to the control PCB with a ribbon cable.

    • It can be removed with 2 screws.

    • The 2 cell battery pack is located under the main PCB.

    crwdns2913378:0crwdne2913378:0

crwdns2862417:0crwdne2862417:0

crwdns2935291:0crwdnd2935291:01crwdnd2935291:0crwdne2935291:0

Markus

crwdns2935283:001/01/20crwdne2935283:0

132 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 3

crwdns2944067:00crwdne2944067:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 2

crwdns2936753:030crwdne2936753:0 9

crwdns2942667:0crwdne2942667:0 766