crwdns2933423:0crwdne2933423:0

crwdns2942213:0crwdne2942213:0

crwdns2935311:0crwdnd2935311:0crwdne2935311:0 crwdns2935313:0HP Creator 930crwdnd2935313:0crwdnd2935313:0crwdne2935313:0

  1. HP Creator 930 Teardown, Inspect the mouse: crwdns2935265:01crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 HP Creator 930 Teardown, Inspect the mouse: crwdns2935265:01crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 HP Creator 930 Teardown, Inspect the mouse: crwdns2935265:01crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
    • The HP Creator 930 Mouse is a mouse aimed at Creative professionals. It offers upto 3 device connections at a time - 2 via bluetooth and 1 via 2.4G dongle.

    • The mouse supports sideways tilt scrolling, and has 4 additional buttons.

    • 3 of the side buttons can be remapped to be used with macros and other functions, via the HP desktop application.

  2. HP Creator 930 Teardown, Flip over the mouse: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Flip over the mouse so that the bottom faces up. The sensor and switch should be visible.

  3. HP Creator 930 Teardown, Open the bottom lid of the mouse: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • The bottom lid of the mouse would be held fastened with a magnet.

    • To open it, you must press the indentation with your thumb and the lid will pop out.

  4. HP Creator 930 Teardown, Remove the sticker: crwdns2935265:04crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 HP Creator 930 Teardown, Remove the sticker: crwdns2935265:04crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • Using a sharp knife or tweezers, try to pry off the sticker that is visible on the mouse. It hides the screws underneath the sticker.

    • Beware - the sticker may not be usable any longer, so you should click a picture for the details mentioned on it.

  5. HP Creator 930 Teardown, Open the screws: crwdns2935265:05crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 HP Creator 930 Teardown, Open the screws: crwdns2935265:05crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    • There are a total of 4 screws that are holding the mouse together.

    • 2 screws are on the top, 1 on the right side, and 1 on the bottom.

    • The screws have a Y-type head, and you may require a suitable screwdriver.

  6. HP Creator 930 Teardown, Pry open the top and bottom halves of the mouse: crwdns2935265:06crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • Prying open the mouse should be fairly easy - just use pressure to pull the top off.

Saksham Seth

crwdns2935283:005/30/25crwdne2935283:0

1 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2947412:00crwdne2947412:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 3

crwdns2936753:07crwdne2936753:0 20

crwdns2936753:030crwdne2936753:0 20

crwdns2942667:0crwdne2942667:0 20