crwdns2934019:0iPad Pro 12.9" 5th Gen Opening Procedurecrwdne2934019:0

crwdns2934021:0crwdne2934021:0

crwdns2934003:0masiku 3 agoMaw 2, 2025crwdnd2934003:0Telogorcrwdnd2934003:06crwdne2934003:0

(crwdns2942739:0crwdne2942739:0)

	[title] Top edge information
	[* black] While the top edge adhesive softens, note the following:
-	[* red] There are ~~two~~ ambient light sensors ~~near~~ the ~~corners~~. *Don't insert your pick more than 1 mm here*.
+	[* red] There are *0.7-cm* cutouts for the ambient light sensors starting *4.1 cm* from each of the side edges. *Don't insert your pick more than 1 mm here*.
	[* orange] The front-facing camera and additional sensors are in the center of the top edge. *Don't insert your pick here—there is less than 1 mm* of adhesive and you may damage the components.
	[* icon_caution] For everywhere else, don't insert your pick more than *5 mm* to avoid damaging the screen.

crwdns2934003:0masiku 3 agoMaw 2, 2025crwdnd2934003:0Telogorcrwdnd2934003:06crwdne2934003:0

(crwdns2942739:0crwdne2942739:0)

	[title] Left edge information
-	[* icon_caution] There are four *2 cm-long* cutouts along the left edge of the screen where the adhesive is very thin. Don’t insert your opening pick more than *2 mm* in these locations to avoid damaging the display:
-	[* red] The ~~upper~~ cutouts begin at *~~4 cm* and *6~~ cm* from the top of the frame.
-	[* orange] The ~~bottom~~ cutouts begin at *~~4 cm* and *6~~ cm* from the bottom of the frame.
+	[* icon_caution] There are four cutouts for flex cables along the left edge of the screen where the adhesive is very thin. Don’t insert your opening pick more than *2 mm* in these locations to avoid damaging the display:
+	[* red] The *2.1-cm* outer cutouts begin at *6.1 cm* from the top and bottom of the frame.
+	[* orange] The *2.8-cm* inner cutouts begin at *10.1 cm* from the top and bottom of the frame.
	[* icon_caution] Everywhere else, don't insert your opening pick more than *5 mm*.

crwdns2933985:0crwdne2933985:0 (position 1)

crwdns2861264:0crwdne2861264:0 (position 1)

	[title] Top edge information
	[* black] While the top edge adhesive softens, note the following:
-	[* red] There are ~~two~~ ambient light sensors ~~near~~ the ~~corners~~. *Don't insert your pick more than 1 mm here*.
+	[* red] There are *0.7-cm* cutouts for the ambient light sensors starting *4.1 cm* from each of the side edges. *Don't insert your pick more than 1 mm here*.
	[* orange] The front-facing camera and additional sensors are in the center of the top edge. *Don't insert your pick here—there is less than 1 mm* of adhesive and you may damage the components.
	[* icon_caution] For everywhere else, don't insert your pick more than *5 mm* to avoid damaging the screen.

	[title] Left edge information
-	[* icon_caution] There are four *2 cm-long* cutouts along the left edge of the screen where the adhesive is very thin. Don’t insert your opening pick more than *2 mm* in these locations to avoid damaging the display:
-	[* red] The ~~upper~~ cutouts begin at *~~4 cm* and *6~~ cm* from the top of the frame.
-	[* orange] The ~~bottom~~ cutouts begin at *~~4 cm* and *6~~ cm* from the bottom of the frame.
+	[* icon_caution] There are four cutouts for flex cables along the left edge of the screen where the adhesive is very thin. Don’t insert your opening pick more than *2 mm* in these locations to avoid damaging the display:
+	[* red] The *2.1-cm* outer cutouts begin at *6.1 cm* from the top and bottom of the frame.
+	[* orange] The *2.8-cm* inner cutouts begin at *10.1 cm* from the top and bottom of the frame.
	[* icon_caution] Everywhere else, don't insert your opening pick more than *5 mm*.