crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

iMac 27寸（2009年下半年至2010年款）显卡更换

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
crwdns2931653:06crwdne2931653:0
iMac Intel 27" (Late 2009 or Mid 2010) Graphics Card Replacement: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 iMac Intel 27" (Late 2009 or Mid 2010) Graphics Card Replacement: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 iMac Intel 27" (Late 2009 or Mid 2010) Graphics Card Replacement: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

  • As the 6 series is slightly higher, we need to make a little space on the plastic holder which is beneath the card.

  • Remove the plastic part, which is shown on the 2nd picture, by removing one screw and carefully pull it from the aluminium case.

  • It's fastened with tape so don't worry about breaking anything.

  • After wiggling and navigating it around the cables, you should have it in your hands.

  • The rectangular space, in picture three where the large cable goes through, use a rotary tool to make it about 5mm wider and 2-3mm deeper.

  • The third image shows the final result we want to achieve.

  • The primary reason for this step is the heatpipe of the 6 series, which takes more space.

  • Note: This is ONLY necessary on the late 2009 model, the 2010 models already have enough room.

6系显卡较高，我们需要在塑料支架上开一点空间。

卸下一颗螺丝，将其从合金外壳中小心的拉出，取下第二张图片所展示的塑料支架。

它被胶带所固定，所以不必但心，您不会弄坏它的。

有一些杂乱的电缆，您应该将他们放入您的手中。

您看到大线缆穿过矩形的空间。 使用锯子或其他工具将其扩大至5mm宽 2-3mm深。

第三张图片展示了最后处理完的样子。

做这一步的原因是为了给6系显卡更多的空间。

注意 这个操作只限于2009款 2010款已经有足够的空间了。

-[* black] As the 6 series is slightly higher we need to make a little space on the plastic holder which is beneath the card
-[* black] Remove the plastic part which is shown on the 2nd picture by removing one screw and carefully pull it from the aluminium case
-[* black] Its fastended with tape, so don't worry, you can't break anything
-[* black] Some wiggling and navigating it from the cables and you should have it in your hands
-[* black] You see the rectangular space where the large cable goes through. Use a saw or other tool to make it about 5mm wider and 2-3mm deeper
-[* black] The third image shows the final result we want to achieve
-[* black] The primary reason for thi step is the heatpipe of the 6 series which takes more space
-[* black] Note: this is ONLY necessary on the late 2009 model, 2010 models already got enough room!
+[* black] As the 6 series is slightly higher, we need to make a little space on the plastic holder which is beneath the card.
+[* black] Remove the plastic part, which is shown on the 2nd picture, by removing one screw and carefully pull it from the aluminium case.
+[* black] It's fastened with tape so don't worry about breaking anything.
+[* black] After wiggling and navigating it around the cables, you should have it in your hands.
+[* black] The rectangular space, in picture three where the large cable goes through, use a rotary tool to make it about 5mm wider and 2-3mm deeper.
+[* black] The third image shows the final result we want to achieve.
+[* black] The primary reason for this step is the heatpipe of the 6 series, which takes more space.
+[* icon_note] Note: This is ONLY necessary on the late 2009 model, the 2010 models already have enough room.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0