crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

如何焊接和拆焊

crwdns2931527:0crwdnd2931527:0crwdnd2931527:0crwdnd2931527:0crwdne2931527:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
crwdns2931653:09crwdne2931653:0
How To Solder and Desolder Connections: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 How To Solder and Desolder Connections: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 How To Solder and Desolder Connections: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

  • You're going to heat the solder pad and the component lead very hot for 2 to 3 seconds. The pad and lead should readily melt the solder wire.

  • Press the tip against the circuit board's solder pad and the component lead for about 1 second to heat them both. Angle the tip so it has maximum contact with the pad and lead.

  • If you're using a narrow soldering tip or working with a large solder pad, you may not be able to transfer enough heat to the area. You can try increasing the temperature by 50°C or switch to a larger tip for more effective heat transfer.

  • If you heat the circuit board continuously for more than 10 seconds, the excessive heat may damage the solder pad or component. Additionally, it could start loosening adjacent components.

  • Feed the solder wire into the heated area until there's a concave pool of solder surrounding the lead.

  • This should happen within a few seconds. If the solder doesn't adhere to the pad, apply flux to the pad or increase the temperature.

  • Don't feed the solder directly onto the tip as it won't flow properly into the pad and lead causing a weak connection.

  • Remove the solder wire, then remove the soldering iron from the solder pad.

您需要加热焊盘和元件引线 2 到 3 秒。焊盘和引线应能迅速熔化焊锡丝。

将烙铁头按压在电路板的焊盘和元件引线上约 1 秒钟，以加热它们。调整烙铁头的角度，使其与焊盘和引线最大程度接触。

如果您使用较窄的焊接头或使用较大的焊盘，则可能无法将足够的热量传输到该区域。您可以尝试将温度提高 50°C 或切换到较大的焊接头，以实现更有效的传热。

如果持续加热电路板超过 10 秒，过高的热量可能会损坏焊盘或元件。此外，它还可能使相邻的元件松动。

将焊锡丝送入加热区域，直到引线周围形成一个凹陷的焊锡池。

这应该会在几秒钟内发生。如果焊料没有粘附到焊盘上，请在焊盘上涂抹助焊剂或提高温度。

不要将焊料直接送入焊头，因为焊料无法正常流入焊盘和引线，导致连接不牢固。

去掉焊锡丝，然后将烙铁从焊盘上移开。

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0