crwdns2933423:0crwdne2933423:0

iPhone 6s の上部コンポーネントケーブルの交換

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:03crwdnd2931529:0crwdne2931529:0

crwdns2935425:014crwdne2935425:0

crwdns2936315:0crwdne2936315:0
crwdns2936323:0crwdne2936323:0
crwdns2931653:014crwdne2931653:0
iPhone 6s Upper Component Cable Replacement: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 iPhone 6s Upper Component Cable Replacement: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 iPhone 6s Upper Component Cable Replacement: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
  • If your replacement part did not come with the mute switch cover, you will need to remove the switch cover and transfer It.

  • Use the flat end of the spudger to press down and hold the old bracket firmly in place.

  • Use tweezers or your fingers to carefully rock the switch cover such that the switch cover pins swing out of their clips.

  • Lift the switch cover straight up.

  • To install the mute switch cover onto the new upper cable assembly, reverse the steps.

  • The pins are supposed to rest near the clip opening. Do no attempt to force the pins far into the clips. The switch cover will be held securely in place once you screw the bracket back onto the case.

  • The switch cover goes on in only one orientation. If you are having a hard time getting the switch cover onto the new part, try toggling the switch so that the black protruding lever is in a different position.

  • Before reassembling the phone, check all switches and buttons to see if they physically work.

交換用のパーツにミュート用スイッチカバーが付いていない場合は、このスイッチカバーを取り出して、交換用パーツに移植してください。

スパッジャーの平面側先端を使って、古いブラケットをしっかりと押し込んで固定してください。

ピンセットまたは指先を使って、スイッチカバーを慎重に揺り動かし、スイッチカバーのピンがクリップから外れるようにします。

スイッチカバーをまっすぐ持ち上げます。

ミュート用スイッチカバーを新しい上部ケーブルアセンブリにインストールするには、手順を逆の順番に従って作業を進めてください。

ピンはクリップの開口部近くに付いているはずです。 ピンをクリップ内側に押し込まないでください。 ブラケットをケースにネジで留めると、スイッチカバーがしっかりと固定されます。

スイッチカバーは、1つの方向でのみでオンになります。 スイッチカバーを交換用パーツに取り付けるのが難しい場合は、スイッチを切り替えて、黒い突き出たレバーが別の位置になるようにします。

デバイスを組み立てる前に、すべてのスイッチとボタンをチェックして、それらが機能するかどうか確認します。

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0