crwdns2933423:0crwdne2933423:0

iPhone 3G 电池更换

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:014crwdnd2931529:0crwdne2931529:0

crwdns2935425:015crwdne2935425:0

crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
crwdns2931653:015crwdne2931653:0
iPhone 3G Battery Replacement, Loosen the battery: crwdns2935265:00crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
Loosen the battery
  • Use a spudger to pry the battery up from the rear case. The battery is attached with an adhesive strip around the perimeter of the battery.

  • To prevent the battery from bending during the removal process, we recommend against using just the plastic pull-tab.

  • Removing the battery is NOT necessary for replacing the GPS antenna. It merely gives you more space for removing the headphone assembly (which is also unnecessary to completely remove).

  • The iPhone's battery is attached to the rear case with a mild adhesive. This adhesive usually comes out attached to the battery. If your replacement battery already includes an adhesive backing, you're all set. If your replacement battery doesn't have an adhesive backing, you'll want to transfer the adhesive from your old battery to the new one.

  • If the battery isn't detaching from the rear case, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Use the flat end of a spudger to gently lift the battery. Allow the alcohol to air dry before installing your new battery.

  • Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

  • You can use a hair dryer or heat gun on its lowest setting to heat the back of the case. This will help loosen the adhesive bond before using the spudger to separate the battery from the case back.

  • Caution: Overheating the iPhone may ignite the battery.

使用spudger撬电池从后盖。电池连接在电池周围的胶条。防止电池在去除过程中弯曲,我们不推荐使用的塑料拉环。*注意:拆卸电池不必要更换GPS天线。它只是给你更多的空间去耳机组件(也没有必要完全删除)。

iPhone的电池连接到后方例轻度粘连。该粘合剂通常是连接到电池。如果你更换电池已经包括粘合剂背衬,你所有的设置。如果你更换电池没有粘合剂背衬,你想从您的旧电池的粘合剂转移到新的。

你可以使用它的最低设置吹风机或热枪热后面的情况。这将有助于松开粘结前使用spudger将电池从表壳背面。

-[* black] Use a spudger to pry the battery up from the rear case. The battery is attached with an adhesive strip around the perimeter of the battery. To prevent the battery from bending during the removal process, we recommend against using just the plastic pull-tab . *Note: Removing the battery is NOT necessary for replacing the GPS antenna. It merely gives you more space for removing the headphone assembly (which is also unnecessary to completely remove).
-[* icon_reminder] The iPhone's battery is attached to the rear case with a mild adhesive. This adhesive usually comes out attached to the battery. If your replacement battery already includes an adhesive backing, you're all set. If your replacement battery doesn't have an adhesive backing, you'll want to transfer the adhesive from your old battery to the new one.
+[title] Loosen the battery
+[* black] Use a spudger to pry the battery up from the rear case. The battery is attached with an adhesive strip around the perimeter of the battery.
+ [* icon_note] To prevent the battery from bending during the removal process, we recommend against using just the plastic pull-tab.
+ [* icon_note] Removing the battery is NOT necessary for replacing the GPS antenna. It merely gives you more space for removing the headphone assembly (which is also unnecessary to completely remove).
+ [* icon_reminder] The iPhone's battery is attached to the rear case with a mild adhesive. This adhesive usually comes out attached to the battery. If your replacement battery already includes an adhesive backing, you're all set. If your replacement battery doesn't have an adhesive backing, you'll want to transfer the adhesive from your old battery to the new one.
+[* icon_note] If the battery isn't detaching from the rear case, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Use the flat end of a spudger to gently lift the battery. Allow the alcohol to air dry before installing your new battery.
+ [* icon_caution] Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.
[* icon_note] You can use a hair dryer or heat gun on its lowest setting to heat the back of the case. This will help loosen the adhesive bond before using the spudger to separate the battery from the case back.
+ [* icon_caution] Caution: Overheating the iPhone may ignite the battery.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0