crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Kit per la soluzione al Cerchio Rosso della Morte su una Xbox 360

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936321:0crwdne2936321:0
crwdns2931653:06crwdne2931653:0
Xbox 360 Red Ring of Death Fix Kit: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Xbox 360 Red Ring of Death Fix Kit: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Xbox 360 Red Ring of Death Fix Kit: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

  • This step is performed with the motherboard out of the chassis.

  • Insert a machine screw through each of the four holes around the CPU heat sink, with their heads on the back side of the board. While you hold the screws in place, sandwich the nylon washer between the motherboard and metal washer.

  • The order of the washers is important. Do not put the metal washer on first.

  • When attaching the CPU heat sink, be sure the fins are aligned with the air flow from the fans (as seen in the third picture). Having the flat side of the fins perpendicular to the air flow will cause your Xbox 360 to overheat.

  • Using the large flathead screwdriver bit, tighten the screws into the CPU heat sink. First lightly tighten the four screws in an X-shaped pattern as seen in the second picture, then follow the same X-shaped sequence to fasten the screws down.

  • Don't be afraid of a bit of tension - the pressure between the heat sinks and processors caused by sufficiently tightened screws is needed to retain the heatsinks.

  • Repeat the same process to attach your GPU heat sink.

Questo passaggio va fatto con la scheda madre fuori dal telaio.

Inserisci una vite a testa cilindrica in ognuno dei 4 fori attorno al dissipatore della CPU, con la testa sul lato posteriore della scheda madre.

Mentre tieni la testa della vite, dall'altra parte infilaci una rondella in nylon, dopodiché infilaci una rondella in metallo.

L'ordine delle rondelle è importante. Non infilare quella in metallo per prima.

Quando reinstalli il dissipatore della CPU assicurati che le alette siano allineate con il flusso d'aria delle ventole (come mostrato nella terza immagine). Posizionare le alette perpendicolarmente al flusso d'aria farà surriscaldare la tua Xbox 360.

Usa la punta piatta più grande per avvitare le viti nel dissipatore della CPU. Prima avvita leggermente le 4 viti procedendo in uno schema a X come mostrato nella seconda immagine, quindi finisci di avvitarle con forza seguendo lo stesso schema.

Non aver paura di applicare forza alle viti: è richiesta una certa pressione tra il dissipatore e la CPU per farli aderire.

Ripeti la stessa procedura per rimontare il dissipatore della GPU.

[* icon_note] This step is performed with the motherboard out of the chassis.
-[* black] Insert a machine screw through each of the four holes around the CPU heat sink, with their heads on the back side of the board.
-[* black] While holding the head of the screw, place a nylon washer ***then*** a metal washer over the threads.
+[* black] Insert a machine screw through each of the four holes around the CPU heat sink, with their heads on the back side of the board. While you hold the screws in place, ***sandwich the nylon washer between the motherboard and metal washer.***
[* icon_caution] The order of the washers is important. ***Do not*** put the metal washer on first.
[* icon_caution] When attaching the CPU heat sink, be sure the fins are aligned with the air flow from the fans (as seen in the third picture). Having the flat side of the fins perpendicular to the air flow will cause your Xbox 360 to overheat.
-[* red] Using the large flathead screwdriver bit, tighten the screws into the CPU heat sink. First lightly tighten the four screws in an X-shaped pattern as seen in the second picture, then follow the same X-shaped sequence to really torque the screws down.
-[* icon_note] Don't be afraid of over-tightening the screws - the pressure between the heat sinks and processors caused by sufficiently torqued screws is needed to squeeze the processors back against the board.
+[* red] Using the large flathead screwdriver bit, tighten the screws into the CPU heat sink. First lightly tighten the four screws in an X-shaped pattern as seen in the second picture, then follow the same X-shaped sequence to fasten the screws down.
+[* icon_note] Don't be afraid of a bit of tension - the pressure between the heat sinks and processors caused by sufficiently tightened screws is needed to retain the heatsinks.
[* icon_reminder] Repeat the same process to attach your GPU heat sink.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0