crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

iPhone4 电池更换

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:018crwdnd2931529:0crwdne2931529:0

crwdns2935421:0crwdne2935421:0

crwdns2935425:03crwdne2935425:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
crwdns2931653:03crwdne2931653:0
iPhone 4 Battery Replacement: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 iPhone 4 Battery Replacement: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 iPhone 4 Battery Replacement: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

  • Use the clear plastic pull tab to gently lift the battery out of the iPhone.

  • If the tab breaks before the battery is freed, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive.

  • Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

  • If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.

  • If your replacement battery came in a plastic sleeve, remove it before installation by pulling it away from the the ribbon cable.

  • Before reconnecting the battery connector, be sure the contact clip (shown in red) is properly positioned next to the battery connector.

  • Before reassembly, clean metal-to-metal contact points with a de-greaser such as windex. The oils from your fingers have the potential to cause wireless interference issues.

  • Perform a hard reset after reassembly. This can prevent several issues and simplify troubleshooting.

用塑料拉手轻轻将电池从机身中拉出。

如果在电池拉出前塑料拉手坏了，沿着塑料拉手方向小心的用手机撬棒在电池背部滑动几下除去胶条。在别的部位可能会造成损坏。

如果你的更换电池采用塑料套管，请在安装前将其从带状电缆中拉出来将其取下。

在扣电池座以前，确保排线接口与电池座位置相符（图中红色区域所示）。

在重新安装电池之前，先对金属接口机油进行处理比如清洁剂。手指上的油脂是潜在的危险对于无线链接模块。

进行强制重启在安装完成后，可以有效的避免一些错乱的状况。

[* black] Use the clear plastic pull tab to gently lift the battery out of the iPhone.
-[* icon_caution] If the tab breaks before the battery is freed, carefully slide a spudger under the battery tab to release the adhesive. Prying in other places may cause damage.
+[* icon_note] If the tab breaks before the battery is freed, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive.
+ [* icon_caution] Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.
+ [* black] If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.
[* icon_note] If your replacement battery came in a plastic sleeve, remove it before installation by pulling it away from the the ribbon cable.
[* red] Before reconnecting the battery connector, be sure the contact clip (shown in red) is properly positioned next to the battery connector.
[* icon_reminder] Before reassembly, clean metal-to-metal contact points with a de-greaser such as windex. The oils from your fingers have the potential to cause wireless interference issues.
[* icon_reminder] Perform a [guide|44489|hard reset] after reassembly. This can prevent several issues and simplify troubleshooting.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0