crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

认识和断开线缆连接头

crwdns2935423:0crwdne2935423:0

crwdns2935425:01crwdne2935425:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
crwdns2931653:01crwdne2931653:0
Recognizing & Disconnecting Cable Connectors, ZIF Connectors: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Recognizing & Disconnecting Cable Connectors, ZIF Connectors: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Recognizing & Disconnecting Cable Connectors, ZIF Connectors: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
ZIF Connectors

  • Zero insertion force (ZIF) connectors are often used to secure delicate ribbon cables of many sizes. A hinged locking flap runs across the top of the socket, and the cable is inserted on one of the long edges.

  • To disconnect the cable, use a spudger, opening tool, or a clean fingernail to flip up the locking flap—this is the unlocked position.

  • Use the widest tool possible to avoid damaging the delicate hinge pins.

  • Once the flap is in the unlocked position, use tweezers or your fingers to gently pull the cable out of its socket.

  • If the cable has a pull tab, use it to grip the cable. You may damage the cable by gripping it directly.

  • Some cables may have small "arms" or notches that help secure them. If this is the case, you'll need to lift the cable to free it and then pull it out.

  • To reconnect, make sure the locking flap is flipped up and gently reinsert the cable. Then, flip the locking flap down to secure the cable. The cable should slide into the socket with little to no force. If you're having trouble, remove it, check that the flap is fully unlocked, and try again.

  • Some cables (like the one pictured) may have a line that marks the edge of the connection area. Make sure you insert the cable so the line is flush with the edge of the socket.

ZIF 接口

零插入力（ZIF）连接器通常会给初学者带来麻烦。 ZIF连接器用于固定精细的带状电缆，如FFC（扁平柔性电缆）或FPC（柔性印刷电路）电缆。

要断开电缆，请使用撬棒、打开工具或干净的指甲向上翻转锁定襟翼——这是解锁位置。

使用尽可能宽的工具，以避免损坏精密的铰链销。

一旦翻盖处于解锁位置，用镊子或手指轻轻地将电缆从插座中拉出。

如果电缆有拉片，请用它来夹住电缆。直接握住电缆可能会损坏电缆。

一些电缆可能具有有助于固定它们的小“臂”或槽口。如果是这种情况，您需要提起电缆以释放它，然后将其拉出。

要重新连接，请确保锁定翻盖向上翻转并轻轻重新插入电缆。然后，向下翻转锁定盖以固定电缆。电缆应以很小的力或没有力滑入插座。如果您遇到问题，请将其取下，检查翻盖是否已完全解锁，然后重试。

某些电缆（如图所示）可能有一条线标记连接区域的边缘。确保插入电缆，使线路与插座边缘齐平。

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0