crwdns2933423:0crwdne2933423:0

Reemplazo de teclado para MacBook Air de 13 pulgadas, mediados de 2011

crwdns2936315:0crwdne2936315:0
crwdns2936331:0crwdne2936331:0
crwdns2931653:02crwdne2931653:0
MacBook Air 13" Mid 2011 Keyboard Replacement, Removing the backlight: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 MacBook Air 13" Mid 2011 Keyboard Replacement, Removing the backlight: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 MacBook Air 13" Mid 2011 Keyboard Replacement, Removing the backlight: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Removing the backlight
  • We have to remove the backlight carefully as not to damage it, if you are replacing this component then you can simply pull it off.

  • The backlight consists of 3 layers, the very fragile backlight covering, a clear plastic layer and a very fragile keyboard layout template. We DO NOT want to damage these in any way if we are to use them again, so ultimate care is needed. They are stuck together but with plenty of care they can be separated.

  • Using a sharp small craft knife or similar, very carefully lift up the surrounding edge of the backlight by running the blade underneath where the adhesive is located, as we do not want to tear this extremely fragile component.

  • Some may suggest to use a heat gun but this will more than likely deform the backlight from the heat, rendering it useless.

  • Once we have a fair sized area lifted we can very gently pull away the backlight using extra care not to tear it. We can use the strength of the middle plastic sheet to assist in lifting it away. Once removed put it to the side as it will be used again in a later stage.

  • We can gently brush or wipe off any stains or debris that may have built up over time using a soft brush or cloth with some alcohol making the part nice and clean ready for re-installation.

Tenemos que quitar la luz de fondo con cuidado para no dañarla, si estás reemplazando este componente entonces puedes simplemente sacarlo.

La retroiluminación consta de tres capas: la cubierta, que es muy frágil, una capa de plástico transparente y una plantilla de distribución de teclado, también muy frágil. No queremos dañarlas de ninguna manera si las volvemos a usar, por lo que es necesario un cuidado extremo. Están pegadas, pero con mucho cuidado se pueden separar.

Insertar traducción aquíUsando un cuchillo artesanal pequeño y afilado o algo similar, levante con mucho cuidado el borde circundante de la luz de fondo pasando la hoja por debajo de donde se encuentra el adhesivo, ya que no queremos rasgar este componente extremadamente frágil.

Algunos pueden sugerir utilizar una pistola de calor, pero es muy probable que esto deforme la luz de fondo por el calor, volviéndola inútil.

Una vez que hayamos levantado un área considerable, podemos retirar la retroiluminación con mucho cuidado para no romperla. Podemos usar la fuerza de la lámina de plástico central para ayudarnos a levantarla. Una vez retirada, déjela a un lado, ya que la volveremos a usar más adelante.

Podemos cepillar o limpiar suavemente cualquier mancha o residuo que pueda haberse acumulado con el tiempo utilizando un cepillo suave o un paño con un poco de alcohol para dejar la pieza limpia y lista para su reinstalación.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0