crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Polaroid I-2 フィルムドア付き背面カバーの取り外し

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:03crwdnd2931529:0crwdne2931529:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936323:0crwdne2936323:0
crwdns2931653:04crwdne2931653:0
Polaroid I-2 Back Cover Removal with Film Door Replacement, Unclip the back cover: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Polaroid I-2 Back Cover Removal with Film Door Replacement, Unclip the back cover: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Polaroid I-2 Back Cover Removal with Film Door Replacement, Unclip the back cover: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Unclip the back cover

  • Releasing the clips requires getting a tool between the covered "thin" edge of the front cover and the clips themselves.

  • Angle an opening pick upward and insert it at the gap where the bottom right corner of the back cover meets the triangular tip of the front cover’s right edge.

  • Push the pick up to get it above the overhanging lip in the back cover.

  • You'll see the plastic warp a little. This is normal.

  • While pushing upward, slowly rotate the pick towards the left edge of the camera until it's under the front cover.

  • The pick can slip out easily, so this may take a few tries.

バックカバーのクリップを外す

クリップを外すには、フロントカバーの「薄い」エッジとクリップの間にツールを入れます。

オープニングピックを上に向けながら、バックカバーの右下コーナーとフロントカバー右端の三角形先端が接する隙間に差し込みます。

ピックを押し上げ、バックカバー右側端の三角形先端付近から張り出した隙間上に差し込みます。

プラスチックが少しゆがんでいるかもしれません。心配いりません、これは正常です。

上方に押し上げながら、ピックをカメラの左端に向かってフロントカバーの下に入るまでゆっくりと回転させます。

ピックは外れやすいので、何度か試す必要があるかもしれません。

[title] Unclip the back cover
-[* icon_note] Releasing the clips requires getting a tool between the covered covered "thin" edge of the front cover and the clips themselves.
+[* icon_note] Releasing the clips requires getting a tool between the covered "thin" edge of the front cover and the clips themselves.
[* black] Angle an opening pick upward and insert it at the gap where the bottom right corner of the back cover meets the triangular tip of the front cover’s right edge.
[* black] Push the pick up to get it above the overhanging lip in the back cover.
[* icon_note] You'll see the plastic warp a little. This is normal.
[* black] While pushing upward, slowly rotate the pick towards the left edge of the camera until it's under the front cover.
[* icon_note] The pick can slip out easily, so this may take a few tries.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0