crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Sostituzione case posteriore con sportello pellicola Polaroid I-2

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:03crwdnd2931529:0crwdne2931529:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936321:0crwdne2936321:0
crwdns2931653:04crwdne2931653:0
Polaroid I-2 Back Cover Removal with Film Door Replacement, Unclip the back cover: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Polaroid I-2 Back Cover Removal with Film Door Replacement, Unclip the back cover: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Polaroid I-2 Back Cover Removal with Film Door Replacement, Unclip the back cover: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Unclip the back cover

  • Releasing the clips requires getting a tool between the covered "thin" edge of the front cover and the clips themselves.

  • Angle an opening pick upward and insert it at the gap where the bottom right corner of the back cover meets the triangular tip of the front cover’s right edge.

  • Push the pick up to get it above the overhanging lip in the back cover.

  • You'll see the plastic warp a little. This is normal.

  • While pushing upward, slowly rotate the pick towards the left edge of the camera until it's under the front cover.

  • The pick can slip out easily, so this may take a few tries.

Sgancia il case posteriore

Aprire i ganci richiede l'inserimento di uno strumento tra il bordo "sottile" del case della parte anteriore e i ganci stessi.

Inclina un plettro di apertura verso l'alto e inseriscilo nella fessura dove l'angolo inferiore destro del case posteriore incontra la punta triangolare del bordo destro del case anteriore.

Spingi il plettro verso l'alto per farlo arrivare sopra il margine che sporge nel case posteriore.

Vedrai che la plastica si deformerà un po'. È normale.

Mentre spingi verso l'alto, ruota lentamente il plettro verso il bordo sinistro della macchina fotografica finché non è sotto il case anteriore.

Il plettro può sfilarsi facilmente, quindi ci potrebbero volere più tentativi.

[title] Unclip the back cover
-[* icon_note] Releasing the clips requires getting a tool between the covered covered "thin" edge of the front cover and the clips themselves.
+[* icon_note] Releasing the clips requires getting a tool between the covered "thin" edge of the front cover and the clips themselves.
[* black] Angle an opening pick upward and insert it at the gap where the bottom right corner of the back cover meets the triangular tip of the front cover’s right edge.
[* black] Push the pick up to get it above the overhanging lip in the back cover.
[* icon_note] You'll see the plastic warp a little. This is normal.
[* black] While pushing upward, slowly rotate the pick towards the left edge of the camera until it's under the front cover.
[* icon_note] The pick can slip out easily, so this may take a few tries.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0