crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

납땜 브리지 해결 방법

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936325:0crwdne2936325:0
crwdns2931653:03crwdne2931653:0
How to Fix a Solder Bridge, Remove the solder bridge: crwdns2935265:00crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 How to Fix a Solder Bridge, Remove the solder bridge: crwdns2935265:00crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
Remove the solder bridge

  • With the solder wick on top of the solder bridge, heat the wick using the soldering iron by pressing on top of the affected area.

  • The solder wick will be very hot! Avoiding touching the area of the wick near the soldering iron.

  • Alternatively, use wire cutters to cut off about 2 cm (0.75") of braid. Use tweezers or needle nose pliers to place it as described above.

  • Continue to apply pressure with the soldering iron to the solder bridge until the solder is melted and absorbed by the wick.

  • A soldering flux can also be used here to aid in the desoldering process by reducing oxide films.

crwdns2935429:0crwdne2935429:0

땜납 브릿지 위에 납땜 심지를 놓고 납땜 인두를 사용하여 해당 부위를 눌러 심지를 가열합니다.

납땜 심지는 매우 뜨거울 것입니다! 납땜 인두 근처의 심지 부분을 만지지 않도록 주의하세요.

대안으로 전선 커터를 사용하여 약 2cm(0.75")의 브레이드를 자르세요. 핀셋이나 바늘코 플라이어를 사용하여 위에 설명한 대로 배치하세요.

납땜이 녹아 심지에 흡수될 때까지 납땜 인두로 납땜 브릿지에 계속 압력을 가하세요.

산화막을 줄여서 납제거 과정을 돕기 위해 납땜 플럭스를 사용할 수도 있습니다.

-[* black] Place the solder wick on top of the solder bridge and heat the wick using the soldering iron by pressing on top of the affected area.
+[title] Remove the solder bridge
+[* black] With the solder wick on top of the solder bridge, heat the wick using the soldering iron by pressing on top of the affected area.
[* icon_caution] The solder wick will be very hot! Avoiding touching the area of the wick near the soldering iron.
[* icon_note] Alternatively, use wire cutters to cut off about 2 cm (0.75") of braid. Use [product|IF145-020|tweezers] or needle nose pliers to place it as described above.
[* black] Continue to apply pressure with the soldering iron to the solder bridge until the solder is melted and absorbed by the wick.
[* icon_note] A soldering flux can also be used here to aid in the desoldering process by reducing oxide films.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0