crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

ロジックボードとヒートシンクの取り外し方法

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:04crwdnd2931529:0crwdne2931529:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936323:0crwdne2936323:0
crwdns2931653:014crwdne2931653:0
How to Remove the Logic Board and Heatsink, Reassembly information: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 How to Remove the Logic Board and Heatsink, Reassembly information: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 How to Remove the Logic Board and Heatsink, Reassembly information: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Reassembly information

  • Your 3.0 mm nut driver may be too long to thread the hex head screw in. Use one of the following techniques to begin threading the screw in:

  • Thread the screw in using your fingertips.

  • Thread the screw in using blunt nose tweezers.

  • Use your T3 Torx driver to install the 1.4 mm screw into the hex head screw. Then, install the hex head screw using the T3 Torx driver. Finally, hold the hex head screw while you remove the 1.4 mm screw.

  • Once the hex head screw is threaded in a few turns, tighten it using your nut driver.

再組み立て情報

3.0mmのナットドライバーでは、六角頭のねじ をねじ込むには長すぎるかもしれません。次のいずれかの方法でネジをねじ込んでください。

指先を使ってネジを通します。

先の鋭利でないピンセットを使ってネジを通します。

T3トルクスドライバーを使って、1.4mmのネジを六角頭のネジに取り付けます。次に、T3トルクスドライバーを使用して六角頭のネジを取り付けます。最後に、1.4mmのネジを取り外す間、六角頭のネジを押さえておきます。

六角頭のネジを数回転ねじ込んだら、ナットドライバーを使って締め付ける。

[title] Reassembly information
[* icon_note] Your 3.0 mm nut driver may be too long to thread the hex head screw in. Use one of the following techniques to begin threading the screw in:
[* black] Thread the screw in using your fingertips.
- [* black] Thread the screw in using blunt nose tweezers.
+ [* black] Thread the screw in using [product|IF145-020-4|blunt nose tweezers].
[* black] Use your T3 Torx driver to [link|https://guide-images.cdn.ifixit.com/igi/pHUWbSOvyfPyVRut.full|install the 1.4 mm screw|new_window=true] into the hex head screw. Then, install the hex head screw using the T3 Torx driver. Finally, hold the hex head screw while you [link|https://guide-images.cdn.ifixit.com/igi/HaKEhKdonwCxNbXT.full|remove the 1.4 mm screw|new_window=true].
[* black] Once the hex head screw is threaded in a few turns, tighten it using your nut driver.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0