crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Reemplazo del puerto MagSafe del MacBook Pro 16" 2021

crwdns2935423:0crwdne2935423:0

crwdns2935425:01crwdne2935425:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936331:0crwdne2936331:0
crwdns2931653:01crwdne2931653:0
MacBook Pro 14" 2021 MagSafe Port Replacement, Unfasten the MagSafe port: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 MacBook Pro 14" 2021 MagSafe Port Replacement, Unfasten the MagSafe port: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 MacBook Pro 14" 2021 MagSafe Port Replacement, Unfasten the MagSafe port: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Unfasten the MagSafe port

  • Use a 2IP Torx Plus driver to loosen (don't remove) the two MagSafe Port set screws a few turns above the frame.

  • In a pinch, you can use a standard T2 Torx driver to loosen these screws. Make sure to apply constant, downward force to prevent stripping.

  • Use your T5 Torx driver to remove the two 2.7 mm-long screws securing the MagSafe port.

  • These screws are not magnetic—be careful not to lose them.

Liberar el puerto MagSafe

Utiliza un destornillador Torx T2 para aflojar los dos tornillos de fijación en el marco que alinean el puerto MagSafe.

No retires estos tornillos. Simplemente aflójelos unas cuantas vueltas por encima del marco.

Dependiendo del estado de tu controlador, una punta Torx T3 podría ser la mejor opción.

Utiliza tu controlador Torx T5 para quitar los dos tornillos 5IP Torx Plus de 2,7 mm de largo que sujetan el puerto MagSafe.

Estos tornillos no son magnéticos; tén cuidado de no perderlos.

[title] Unfasten the MagSafe port
-[* red] Use a T2 Torx driver to ***loosen*** the two set screws in the frame that align the MagSafe port.
- [* icon_note] Don't remove these screws. Just loosen them a few turns above the frame.
- [* icon_note] Depending on the condition of your driver, a T3 Torx bit might fit best.
-[* orange] Use your T5 Torx driver to remove the two 2.7 mm-long 5IP Torx Plus screws securing the MagSafe port.
+[* red] Use a 2IP Torx Plus driver to ***loosen*** (don't remove) the two MagSafe Port set screws a few turns above the frame.
+ [* icon_note] In a pinch, you can use a standard T2 Torx driver to loosen these screws. Make sure to apply constant, downward force to prevent stripping.
+[* orange] Use your T5 Torx driver to remove the two 2.7 mm-long screws securing the MagSafe port.
[* icon_note] These screws are not magnetic—be careful not to lose them.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0