crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

MacBook Pro (14 Zoll, 2021) MagSafe Anschluss tauschen

crwdns2935423:0crwdne2935423:0

crwdns2935425:01crwdne2935425:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936319:0crwdne2936319:0
crwdns2931653:01crwdne2931653:0
MacBook Pro 14" 2021 MagSafe Port Replacement, Unfasten the MagSafe port: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 MacBook Pro 14" 2021 MagSafe Port Replacement, Unfasten the MagSafe port: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 MacBook Pro 14" 2021 MagSafe Port Replacement, Unfasten the MagSafe port: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Unfasten the MagSafe port

  • Use a 2IP Torx Plus driver to loosen (don't remove) the two MagSafe Port set screws a few turns above the frame.

  • In a pinch, you can use a standard T2 Torx driver to loosen these screws. Make sure to apply constant, downward force to prevent stripping.

  • Use your T5 Torx driver to remove the two 2.7 mm-long screws securing the MagSafe port.

  • These screws are not magnetic—be careful not to lose them.

MagSafe Anschluss losschrauben

Löse die beiden Torx T2 Madenschrauben im Rahmen, die den MagSafe-Anschluss ausrichten.

Entferne die beiden Schrauben nicht. Drehe sie nur wenige Umdrehungen über dem Rahmen auf.

Je nach Zustand des Schraubendrehers passt ein T3 Bit wahrscheinlich am besten.

Nimm einen Torx T5 Schraubendreher und entferne die beiden 2,7 mm langen 5IP Torx Plus Schrauben, mit denen der MagSafe-Anschluss befestigt ist.

Diese Schrauben sind nicht magnetisch, sei vorsichtig und verliere sie nicht.

[title] Unfasten the MagSafe port
-[* red] Use a T2 Torx driver to ***loosen*** the two set screws in the frame that align the MagSafe port.
- [* icon_note] Don't remove these screws. Just loosen them a few turns above the frame.
- [* icon_note] Depending on the condition of your driver, a T3 Torx bit might fit best.
-[* orange] Use your T5 Torx driver to remove the two 2.7 mm-long 5IP Torx Plus screws securing the MagSafe port.
+[* red] Use a 2IP Torx Plus driver to ***loosen*** (don't remove) the two MagSafe Port set screws a few turns above the frame.
+ [* icon_note] In a pinch, you can use a standard T2 Torx driver to loosen these screws. Make sure to apply constant, downward force to prevent stripping.
+[* orange] Use your T5 Torx driver to remove the two 2.7 mm-long screws securing the MagSafe port.
[* icon_note] These screws are not magnetic—be careful not to lose them.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0