crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

更换 Steam Deck 的右扳机

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:09crwdnd2931529:0crwdne2931529:0

crwdns2935423:0crwdne2935423:0

crwdns2935425:01crwdne2935425:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
crwdns2931653:01crwdne2931653:0
Steam Deck Right Trigger Replacement, Unclip the right trigger: crwdns2935265:00crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Steam Deck Right Trigger Replacement, Unclip the right trigger: crwdns2935265:00crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
Unclip the right trigger

  • The right trigger will be on your left-hand side when working on the Steam Deck, as it's laying upside down.

  • The Steam Deck's triggers clip into place on two pegs on the trigger bracket, which doubles as the hinge.

  • Place the flat end of a spudger onto the inside edge of the trigger's right clip.

  • Pivot the trigger clip out, away, and up from the peg to unlatch it.

  • During reassembly, latch the outermost peg first. Once in place, push down on the trigger to latch the innermost peg, producing an audible "click" sound.

  • Check to make sure that the trigger spring is properly aligned. Test the trigger action before continuing reassembly.

松开右扳机

在拆卸时，因为是机器的背面向上，所以更换的时候右扳机会在你的左手边。

Steam Deck 的扳机是通过两个圈扣固定在支架上的。同时这两个圈口还作为扳机的开合铰链。

用撬棒的平头伸到右边的扣环。

用撬棒将扳机的圆扣向右挑然后挑起，以松开他们的连接。

组装的时候先从外侧的扣环开始组装，套入后再套内侧的环扣。套入环扣时如听到“咔”的一声，那么证明环扣已经套好。

检查下扳机的弹簧的位置，测试下扳机好不好用再继续组装

[title] Unclip the right trigger
-[* icon_note] The ***right*** trigger will be on your ***lefthand side*** when working on the Steam Deck, as it's laying upside down.
+[* icon_note] The ***right*** trigger will be on your ***left-hand side*** when working on the Steam Deck, as it's laying upside down.
[* icon_note] The Steam Deck's triggers clip into place on two pegs on the trigger bracket, which doubles as the hinge.
[* black] Place the flat end of a spudger onto the inside edge of the trigger's right clip.
[* black] Pivot the trigger clip out, away, and up from the peg to unlatch it.
[* icon_reminder] During reassembly, latch the outermost peg first. Once in place, push down on the trigger to latch the innermost peg, producing an audible "***click***" sound.
[* icon_note] Check to make sure that the trigger spring is properly aligned. Test the trigger action before continuing reassembly.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0