crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Sustitución de la correa para la cabeza de HIFIMAN Sundara

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936331:0crwdne2936331:0
crwdns2931653:04crwdne2931653:0
Re-attach the Drivers

  • As the design of the headband is ambipolar, which side of it is designated as the left or right side does not matter.

  • Before inserting the drivers back into the headband, make sure the metal place holders that secure driver length are correctly inserted at the start of the interface. The small spheroidal convex indentation of this piece should have the convex (protruding) side facing outwards which will interface with the concave indentations on the drivers.

  • To verify that the metal placeholders are properly installed: if the inner part of the Interface that attaches the headstrap to the headband can be closed with ease (must be actively held together), and the driver being inserted correctly locks in place, the metal place holders have been correctly installed and you may proceed onwards.

  • Make sure the metal fasteners have the correct polarity, either L or R, facing on the inside.

  • After ensuring that the metal fasteners are facing the correct direction, slide the drivers back into the headband and firmly press closed the Interface as shown in the video.

Vuelve a conectar los controladores

Como el diseño de la cinta para la cabeza es simétrico, no importa qué lado tomes como como izquierdo o derecho.

Antes de volver a insertar los controladores en la cinta para la cabeza, asegúrate de deslizar los soportes metálicos, uno para cada controlador, en el ajuste de extensión.

Asegúrate de que los soportes de metal tengan la letra escrita, ya sea L o R, mirando hacia adentro.

Después de asegurarte de que los sujetadores estén orientados en la dirección correcta, desliza los controladores nuevamente dentro de la cinta para la cabeza y presiona firmemente para cerrar la unión de plástico de la correa y la cinta para la cabeza como se muestra en el video.

[title] Re-attach the Drivers
-[* black] As the design of the headband is ambipolar, which side is designated as the left or right side does not matter.
-[* black] Before inserting the drivers back into the headband, make sure to slip on the metal fasteners, one for each driver, onto the extension adjustment.
-[* black] Make sure the metal fasteners have the written polarity, either L or R, facing on the inside.
-[* black] After ensuring the fasteners are facing the correct direction, slide the drivers back into the headband and firmly press closed the plastic headstrap-headband interface as shown in the video.
+[* black] As the design of the headband is ambipolar, which side of it is designated as the left or right side does not matter.
+[* black] ***Before inserting the drivers back into the headband, make sure the metal place holders that secure driver length are correctly inserted at the start of the interface. The small spheroidal convex indentation of this piece should have the convex (protruding) side facing outwards which will interface with the concave indentations on the drivers.***
+[* black] ++***To verify that the metal placeholders are properly installed:***++ if the inner part of the Interface that attaches the headstrap to the headband can be closed with ease (must be actively held together), and the driver being inserted correctly locks in place, the metal place holders have been correctly installed and you may proceed onwards.
+[* black] Make sure the metal fasteners have the correct polarity, either L or R, facing on the inside.
+[* black] After ensuring that the metal fasteners are facing the correct direction, slide the drivers back into the headband and firmly press closed the Interface as shown in the video.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0