crwdns2933423:0crwdne2933423:0

Sostituzione schermo Nintendo Switch

crwdns2935443:0crwdne2935443:0

= crwdns2915112:0crwdne2915112:0 = crwdns2861241:0crwdne2861241:0
crwdns2936315:0crwdne2936315:0
crwdns2936321:0crwdne2936321:0
    Follow this guide to replace a broken or faulty screen on the Nintendo Switch game console. ***This procedure replaces both the LCD panel and the digitizer as a whole unit.*** To replace just the digitizer, follow [guide|140040|this guide]. To replace just the LCD panel, follow [guide|117395|this guide].
    The Switch uses JIS screws, butand the guide is written to reflect this. JIS #00 drivers are specified. You can use a JIS #000 if you can't obtain a JIS #00. You can use a Phillips #000 screwdriver in a pinch. Be, but be very careful not to strip the screws. iFixit's Phillips bitsIf you are designed to be cross-compatiblehaving difficulty with JIS-stylethe screws, you may find that switching drivers helps, even if the drivers are the same size and type.
    ***Note:*** When you remove the shield plate, you’ll need to replace the thermal compound between the plate and the heatsink. Since normal thermal paste isn’t designed to bridge large gaps, the closest replacement is K5 Pro viscous thermal paste. You will, however, need regular replacement thermal paste for the CPU.
    You can complete this repair without removing the heat sink and the game card reader, but it makes disconnecting and reconnecting the LCD panel ribbon cable much more difficult. Keep this in mind when you perform this repair.
    ***Note:*** This guide, and the part we sell, are compatible with the original Nintendo Switch model released in 2017, as well as the newer refreshed model released in 2019 (model numbers HAC-001 and HAC-001(-01), respectively).
      Compare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing.
      To reassemble your device, follow these instructions in reverse order.
      '''***If your new screen doesn’t work properly after you boot up the device, turn it back off and disconnect and reconnect the battery connector.'''***
      Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
      Repair didn’t go as planned? Try some [[Troubleshooting Problems After a Repair|basic troubleshooting]], or ask our [link|https://www.ifixit.com/Answers/Device/Nintendo%20Switch|Nintendo Switch Answers community] for help.

      crwdns2931349:0crwdne2931349:0

      crwdns2936071:01crwdne2936071:0

      Usa uno strumento di apertura, uno spudger o un'unghia per ruotare verso l'alto l'aletta di bloccaggio incernierata sul connettore ZIF del cavo a nastro dello schermo.

      crwdns2936071:02crwdne2936071:0

      Usa un paio di pinzette per sfilare il cavo a nastro dalla sua presa sulla scheda madre.

      crwdns2936071:03crwdne2936071:0

      Usa uno strumento di apertura, uno spudger o un'unghia per ruotare verso l'alto l'aletta di bloccaggio incernierata sul più piccolo connettore ZIF del cavo a nastro dello schermo.

      crwdns2936071:04crwdne2936071:0

      Usa un paio di pinzette per sfilare il cavo a nastro dalla sua presa sulla scheda madre.

      crwdns2936071:05crwdne2936071:0

      Scalda un iOpener e appoggialo al bordo inferiore dello schermo per un paio di minuti per ammorbidire l'adesivo.

      crwdns2936071:06crwdne2936071:0

      Fai aderire una ventosa all'angolo in basso a sinistra dello schermo.

      crwdns2936071:07crwdne2936071:0

      Fai scorrere il plettro sotto il bordo inferiore dello schermo per tagliare l'adesivo.

      crwdns2936071:08crwdne2936071:0

      Infila un secondo plettro nella fessura a sinistra del primo plettro.

      crwdns2936071:09crwdne2936071:0

      Scalda il bordo sinistro dello schermo per un paio di minuti per ammorbidire l'adesivo.

      crwdns2936071:010crwdne2936071:0

      Continua a far scorrere il plettro attorno all'angolo in basso a sinistra per tagliare l'adesivo.

      crwdns2936071:011crwdne2936071:0

      Continua a far scorrere il plettro sotto il bordo sinistro dello schermo per tagliare l'adesivo.

      crwdns2936071:012crwdne2936071:0

      Scalda il bordo superiore dello schermo per un paio di minuti per ammorbidire l'adesivo.

      crwdns2936071:013crwdne2936071:0

      Continua a far scorrere il plettro attorno all'angolo in alto a sinistra dello schermo per tagliare l'adesivo.

      crwdns2936071:014crwdne2936071:0

      Continua a far scorrere il plettro sotto il bordo superiore dello schermo per tagliare l'adesivo.

      crwdns2936071:015crwdne2936071:0

      Scalda il bordo destro dello schermo per un paio di minuti per ammorbidire l'adesivo.

      crwdns2936071:016crwdne2936071:0

      Solleva il bordo destro dello schermo dal dispositivo, facendo passare i cavi a nastro attraverso la cornice.

      crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0